Jump to content
SAU Community

God Damn Hit And Run! Need Panel Beater West


Recommended Posts

Some fu%k with hit my car while my car was parked in Sunshine behind BILO. Left a nice huge dint in it. I've used the 'search' button for panel beater but none around the west area. Does anyone know any good panel beaters around the west (Sunshine?) area that had some good experience with them?

I've uploaded a pix of the dint with my phone camera.... NOT HAPPY JANE.

Someone can help me that would be great asap. I'm not having a good week :D

post-854-1131434793.jpg

f**k wholey shit! I hope the wheel on the car of this person who did this comes off when driving home and they smash into a pole. That sucks big time man, good luck with getting it fixed. God damn scum bags.

i had a similar type of damage done to my car... same side.. same place

its a sh*t place coz you have to spray the whole area up until the roof and then blend it in. Worse place to get damage I rekkon.

I had superstar panels in Dandy area do mine. Not your area but they are reputable, if you want you can check out my car to prove their workmanship... paint matching was brilliant too.

And the price was good too... they admitted they quoted me an incorrect price but had to stick by it.

PM me for more details

Dude, I think Sunshine has more panel beaters than any other suburb. Just cruise down McIntyre Rd and you're bound to find at least 10. There's JJJ, Western Star Prestige, etc.. If you want someone super cheap, check out Yes! Bodyworks (but you really get what you pay for). A really good and cheap place is Jac Smash Repairs. That's at 3 Mullenger St Braybrook (Don't know why it's called Braybrook, it's pretty much Sunshine). Good Luck!

Dude, I think Sunshine has more panel beaters than any other suburb. Just cruise down McIntyre Rd and you're bound to find at least 10. There's JJJ, Western Star Prestige, etc.. If you want someone super cheap, check out Yes! Bodyworks (but you really get what you pay for). A really good and cheap place is Jac Smash Repairs. That's at 3 Mullenger St Braybrook (Don't know why it's called Braybrook, it's pretty much Sunshine). Good Luck!

I know there are alot of panel beaters, but I just want to know ppls experience with the panel beaters and some that have some experience with R33s.

Ron Mace Pannels

Bakers Rd., Coburg Nth (not sure of exact number but somewhere about 85-105)

Melways: Map 17, E8

Contact: Marcus

M:0421169969

They fixed my car and am very happy with the repair and full respray.

OR

Contact Troy (YLWGTR2), via PM

If he can't do the job, he will point you in the right direction.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What copper washer do you guys use on the bleeder bolts? The existing one I have I had no idea where to find it in a local store, I did buy some online but that are only 1mm thick whereas my old one is 2mm+ thick and when I put the new washer out and squeeze the top radiator hose I can hear a bit of air but not with the old one. Does this matter? The new one doesn't leak, but the inner diameter is a bit loose whereas the old one threads on the bolt.
    • Howdy all, after being out a few weeks ago on a spirited drive in my GTR I have 2 issues that oddly have appeared at the same time. Whilst accelerating quickly through the gears all of a sudden i’ve lost power at the top of third gear (below redline around 6000rpm) for no obvious reason.    From that point onwards the car has been running rich on idle, won’t really rev under load without a ton of black smoke and the odd backfire, and dying as a pull up to a set of lights unless I keep the revs up around 1500rpm. In addition when shutting down the car that same night (I was 10 minutes from home) I noticed one of the turbos was significantly noisy on wind down when shutting off the engine. After letting the car cool down overnight it starts up fine, although once it gets to temp the revs start to creep up and down, the exhaust is darker than it should be and it also sounds like it’s running rich (fat note) I’ve put a new set of plugs in it - no change, the old plugs all seemed OK with two of them being somewhat richer/fueled up than the other 3 with 1 being borderline. I’ve smoked tested the intake system via the front of the Turbos, found a split vacuum hose going to the factory boost gauge sender, which I have since replaced.  Also found another leak on the gasket coming off the rear turbo outlet, have also replaced this. After fixing both of these leaks - still have the running rich issue. I’ve also tried another pair of AFM’s - no change here After pulling off the front turbo intake pipes, there is obvious shaft play in the front turbo, which now hisses loudly on light revvs although I can’t see why this would make the car run funny even under idle. I’m curious to know why it’s running rich before I potentially replace/rebuild turbos. The car is completely stock <50,000kms  other than an exhaust. Oil and coolant are all clear. I haven’t bothered with coil packs as it looks like they won’t be the issue due to condition of the plugs. Any help appreciated as I cry myself to sleep!
    • No probs at all. I used to love trying to dig up obscure info for those in need where possible going back 20+ years on SAU.  I did have another look and couldn't come up with any closer match. I'm leaning towards those skirts in your first pic are custom fitments, cut down/extended or from another car entirely and modded to fit an R34 sedan. I would've thought someone in Japan had them and taken a photo at some stage over the last 2 decades but there's nothing. Someone out there must know surely.
    • Welcome mate. Any pics? Even with a DE I'd be well happy if I had that as a 1st car. 
×
×
  • Create New...