Jump to content
SAU Community

Recommended Posts

got a new bov otherday, and today i wacked it on and was adjusting it, i think it was a bit loose as the idle was up and down a fair bit, anyways i took it for a spin and getting up the street it became really bad didnt really wana drive juste idle serge, only traveled 200m odd, anyways i limped it home, and tighteded it up and got it idleing normal, but i have noticed its blowing a little black smoke, as i tightened it up more, the smoke got less and less, now i DID do a search on it and i found black smoke usualy means running rich, and my car runs slightly rich but can my bov's spring tension effect how rich it can run??? im a little worried to drive it now, no performance loss or anything, all idles the same now just a slight haunt of black smoke now, any ideas?

and yes i will put original bov back on tomorro

cheers guys

Link to comment
https://www.sau.com.au/forums/topic/94085-black-smoke/
Share on other sites

atmo mate, and unless i have it that tight taht it wont vent proply and get flutter, when it was idling like a pig it vented awsome, but its that tight now i get reversion, my old bov was the same and was tuned with reversion and really tight , but it shouldnt really matter should it

Link to comment
https://www.sau.com.au/forums/topic/94085-black-smoke/#findComment-1699282
Share on other sites

Unless it's open the whole time in which case it'll do what you're saying.

Turn you engine on, open the hood and look at the bov.

Pull lightly on the accellorator cable to rev the engine and see if the bov is opening. Don't rev too hard only a little. If it's opening it's too loose.

Link to comment
https://www.sau.com.au/forums/topic/94085-black-smoke/#findComment-1700378
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...