Jump to content
SAU Community

Recommended Posts

  • Replies 53
  • Created
  • Last Reply

Top Posters In This Topic

Rev210, no I dont have 33 timing maps.

To reset the ecu, I just used to disconnect the battery and wait for the interior light to fade compeletly. Then reconnect and take your car for a thrash :P NB, its always good to warm your car up before doing a reset, so when you do go for a spin, you arent thrashing a cold engine.

and for those intereseted, I just bought 20L drum or tolulene from Westfuels, 543? Abernathy rd kewdale for $66, works out at $3.30 per litre.

Just wondering steve.. roughly how long would it take? Impul, i heard the footbrake method dosn't really work. But i guess it'll make sense as it's draining out the battery by supplying voltage to the rear brakelights.

you obviously dont understand electronics then, most circutry contains capacitors. Capcacitors store power the same way a batery does. a few seconds without a battery conected wont rest much except yor radios memory and clock.

by putting ya foot on the brake it creats a circut and drains all available power.

I use this method and it works every time

Hrmm? Capacitors? To keep the hold enough current to keep the clocks and all running for about an hr? Woouldn't that take a lot? To drain a capacitor, u need to short it to ground or something right? So pressing the brake pedal connects it straight to ground? Capacitors usually are used to regulate power, it does store a charge... uh... i dunno, all those years of studying electronics in school and i still don't know shit about them. Hahaha. I'm just a dumbass. :P

you obviously dont understand electronics then, most circutry contains capacitors. Capcacitors store power the same way a batery does. a few seconds without a battery conected wont rest much except yor radios memory and clock.

by putting ya foot on the brake it creats a circut and drains all available power.

I use this method and it works every time

LOL, and by having an interior (or the boot light on for R33) it does the same thing, when the light dies, the power is gone.

I used this method and it has worked every time.

You may enjoy playing with your brake pedal, but there are easier ways that are just as effective.

Rev210, no I dont have 33 timing maps.

To reset the ecu, I just used to disconnect the battery and wait for the interior light to fade compeletly.  Then reconnect and take your car for a thrash :)  NB, its always good to warm your car up before doing a reset, so when you do go for a spin, you arent thrashing a cold engine.

and for those intereseted, I just bought 20L drum or tolulene from Westfuels, 543? Abernathy rd kewdale for $66, works out at $3.30 per litre.

thanks for that handy bit of information

i have been hunting around for a couple of days for the stuff

is good to know it is just up the road from me

you obviously dont understand electronics then, most circutry contains capacitors. Capcacitors store power the same way a batery does. a few seconds without a battery conected wont rest much except yor radios memory and clock.

by putting ya foot on the brake it creats a circut and drains all available power.

I use this method and it works every time

What steve said ^^

I understand a little of electronics mate - If you break the circuit to the battery ie - taking the earth away then how will pressing the brake pedal do anything? If the circuit isn't complete how can a current be drawn? The capacitors wouldn't take long to stop holding charge considering it isn't really that high a voltage that runs in the car yeh?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...