Jump to content
SAU Community

Recommended Posts

For sale: Skyline GT-R rear strut brace

Item Condition: Very Good Condition (see pictures)

Reason for Selling: I dont own a skyline and this was still left in the shed from when we were wrecking a GT-R a while ago.

Extra Info: Apparently is a genuine Skyline GT-R N1 rear strutbrace (came standard), this is what I was told. Correct me if I am wrong

Pictures: Pictures are posted below

Contact Details: PM me, or email [email protected] or please feel free to ring me on 0409 576 814 (optus)

Location: Gold Coast, Queensland, Aust.

Price and Payment Conditions: $170 o.n.o (negotiable), Direct deposit.

Delivery & Conditions of Delivery: pick up, or send interstate at buyers expense.

NB:Please dont ask if I have any other parts for GT-R cause this is the only thing left.

pic11so.jpg

pic27ib.jpg

pic31aj.jpg

pic41lu.jpg

pic57qo.jpg

do you know what model its for??

R32 or R33 ??

if its R32 im quite interested

have tried to ring you no answer

Thanks

RellikZephyr

Edited by RellikZephyr
  • 2 weeks later...

Sorry guys back up forsale again (money refunded....my mistake). The strut brace is to suit R33 not R32 (I found out when I went to test fit it).

Lesson learnt: Never trust anyones word, always only trust yourself.

Back up for sale people

R33 rear strut brace. :)

It's clearly a R33 strut brace. And it will fit a Series 1 or 2 R33 GTSt as well.

Thanks buddy.

I dont own a skyline myself and was only going off a friends word, turned out it was for R33 like you said and so I feel bad for stuffing the first buyer around (sorry Nathan :) ).

So umm yeah as you can see its in good condition.

  • 2 weeks later...
  • 3 weeks later...

BUMP. This strut brace is still forsale, so far many people have either called or PM'd me saying they are coming to pick it up but it is still forsale. I know its a long shot since everyone is poor after xmas (me also) but I am willing to wait for this to sell. Offer me the right money and it could be yours.

I have $170 ono on it, so you come up with an offer. I knocked people back that said $100 to me, cause that is way too cheap and is not NEAREST offer. If you make an offer that I am happy with, then I will go down to the post office and get a price on shipping to Sydney. I have had too many people say they want it, and then I drive all the way down to the post office to get a price, I get back to them with the price and hear nothing about it from then on. So if you are keen let me know.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
×
×
  • Create New...