Jump to content
SAU Community

Recommended Posts

I just installed a boost controller and running 1 bar, tonight i took the car out for a spin and when i'm driviing in 3 or 4th the car just slows down as if its down shifting or something (for 2secs) then comes back to normal (it actually did it a few time).

the car is still running the stock exhaust, apart from the boost controller and a blitz bov the car is stock.

I'm guessing slipping clutch, but i've never driven a car with a slipping clutch, any ideas??

also what does a slipping clutch feel like??

Link to comment
https://www.sau.com.au/forums/topic/9546-slipping-clutch/
Share on other sites

Originally posted by meggala

there is also a boost cut at aoround 12 psi or so which could be causeing the problem

thanks meggala, that actually sounds right, i'll run 0.8 until i put the exhaust on. how does one overcome the boost cut off

Link to comment
https://www.sau.com.au/forums/topic/9546-slipping-clutch/#findComment-144912
Share on other sites

when you say it feels like the brakes have been applied, is it like someone has SLAMMED them on hard, or is it like they are being applied gently?

I'm guessing it's the first, as at 1 bar, you are definately hitting the boost cut, and with a std exhaust and standard intercooler, your AFM will be maxing out! If your intercooler is stock, and you have set the ebc for 1 bar, your turbo is producing almost 2 bar, to make up for the preassure drop accross the intercooler!!!!

Keep it at this setting and your turbo wont last long at all, especially with a SII R33.

Wind it down to 0.7 bar (no more), and let us know how you go...

Even when you upgrade your intercooler and exhaust (and intake), I would not be going past 0.8 bar with the stock turbo.... if you want it to live...

Zahos

Link to comment
https://www.sau.com.au/forums/topic/9546-slipping-clutch/#findComment-145089
Share on other sites

I ran 14 pound on my stocky for bloody ages and nothing happend. And if its not your clutch i dont know how or why someone said it was but its not. Slipping clutch the car will just rev up but wont pull. From what your saying its not reving up. So it aint your clutch.

Either boost cut or your talking bout the standard R33 standard ecu flat spot that we have all enjoyed.

Link to comment
https://www.sau.com.au/forums/topic/9546-slipping-clutch/#findComment-145493
Share on other sites

thanks everyone for your replies.

well it appears that it was hitting the boost cut off, cause i reduced the boost to 0.8 and increated the duty cycle and it seems fine. but there is a noise from the boost controller unit in the engine bay when it hits boost, apparently thats normal any comment would be appreciated

Link to comment
https://www.sau.com.au/forums/topic/9546-slipping-clutch/#findComment-152947
Share on other sites

boost cut often feels like you've hit a brick wall... the motor loses revs really quickly, and it can shake the whole car up if your pushing hard....

as for the boost controller... it would be bleeding air off when you reach the stock boost level, as it needs to maintain a level below stock boost at the wastegate, but the boost that the controller (between manifold and wastegate) is seeing is still rising... so there will be air being released... it should be a reasonably quiet sound... but u might be able to notice it...

Link to comment
https://www.sau.com.au/forums/topic/9546-slipping-clutch/#findComment-153068
Share on other sites

i bet your car feels quicker with 0.8 bar boost than at 1 bar with the stock cooler and exhaust, coz at 1 bar with stock cooler and exhaust u r producing more heat than power, and u can say bye bye to your turbo as it will be running nearly 2 bar as Zahos said!!

people still dont understand that more boost doesent always mean more power!:(

Link to comment
https://www.sau.com.au/forums/topic/9546-slipping-clutch/#findComment-153179
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
×
×
  • Create New...