Jump to content
SAU Community

Recommended Posts

I have a 93 R32 GTST its auto.

In the morning it runs really really slugish up to 3000rpm for about a mintue or so although if you go high the turbo comes on like a switch, after its been about a minute or so its fine. I have a GCG turbo rom tune gtr injector 040 fuel pump FMIC exhaust and pod.

It has only been happening since the tune I had although tuner said all the air fuel ratios are all good and at first thought it was the auto, i also thought this however i tried to rev it in neutral and it revs very slow too just like how it runs.

Anyone have any idea wat it is?

I know to drive slow when its cold but yeah this is very slow and realy have to be carefull with traffic sorta slow

Link to comment
https://www.sau.com.au/forums/topic/97020-slugish-cold-start-issue/
Share on other sites

its designed to do this. when the engine is cold (water temp sensor) the ecu retards the timing and adds extra fuel to heat the engine up. during this stage the engine will feel a little flatter and lack response until its heated up. once water temp is around 50deg then its goes to minor level corrections. 80deg is ideal water temp with no correction at all.

also bearing in mind everything else on the car is cold too, diff, gearbox, clutch, bearings etc so its a good thing it lacks response and doesnt come on full stream ahead, prevent bearing / seal excess wear/damage

nah it shouldnt matter how much power it has got. the maps which tell the engine what ign timing and fuel parameters to add for the low load / cruise areas (around 3000rpm ish) wont be any different to your max power tune map areas. the ecu has correction "maps" or settings. these are based on water temp, battery voltage, knock values, air temp (if supported), airflow value and so on.

so based on certain environements the engine is dealt dynamic changes around its environment.

ie when the engine is cold is runs less conservative timing and runs more fuel then when its fully warm. when the engine picks up lots of knock it backs off the timing to protect itself. when the engine detects too much airflow (ie: failed wastegate spring) it protects itself by retarding the timing a lot and dump fuel to richen itself up and try and keep it as safe as possible. when the airflow meter doesnt measure any voltage is does a dynamic rev limit change to 2500rpm. it assumes some air is coming in to allow the engine to run in limp mode but it wont let you rev past, this prevents you from possibly leaning the engine out and causing damage

i also have a rb20det auto R32 and mine does exactly the same thing, very annoying, but once the temp gauge hits the "warmed up" point, you can feel the engine suddenly pick up power. i think the fact we have auto prob "exaggerates" the sluggish feeling.

yeah i just thought it was a bit odd since i have only ever noticed it since tune of the standard computer. Maybe something was fixing in the computer which is why it didn't do it before. Oh well supose ill deal with it. It is a good thing i supose just can't cross the road unless i have a big gap

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'd be worried about having to parallel park a boat like that. Magnificent car though.
    • This car has run before on this z32 ecu can get the part number for you, I have tried with no AFM it didn’t change anything, I compression tested today 140-150 across all 6 cylinders, also set fuel pressure to 43psi. The only weird thing was cylinder 1 plug was black and fouled other 5 cylinders were just wet with fuel. Spun cas by hand and confirmed injectors are clicking 
    • Since you came here to ask for help, have you thought about answering our questions, that might help us lead you to why it was skipping, or have you given up on getting advice?
    • A 1.5 way is a 2 way. It is just a 2 way with a less aggressive ramp on overrun.
    • The ABS and/or TCS being missing/broken will not cause the engine to misbehave. It just casues CEL to come on and annoy you. The CEL is useless if it is always on, so you have to do the things you have to do to get rid of it, so it can be useful. Being a Stag ECU, then yes, it will not expect TCS to be present. But it will expect ABS to be present and working. You will need to either make the ABS CU talk to the ECU (don't ask me what that will take on an NA R34), and make sure the hardware is working....or, you just need to blank it out in Nistune. Do not persist with the stock ECU. You will just have problems. Gte it Nistuned. Start from there. DO YOU HAVE A BOOST SENSOR? The ECU's boost sensor that it. It is connected to the loom at the rear of the coil cover. Usually rides on the firewall on an R34, but is usually bolted down to a bracket along with all the other crap at the back of the coil cover when a Neo is dropped into another car. If you do not have it, the ECU will shit the bed. So, do you have one?
×
×
  • Create New...