Jump to content
SAU Community

Recommended Posts

I have a 93 R32 GTST its auto.

In the morning it runs really really slugish up to 3000rpm for about a mintue or so although if you go high the turbo comes on like a switch, after its been about a minute or so its fine. I have a GCG turbo rom tune gtr injector 040 fuel pump FMIC exhaust and pod.

It has only been happening since the tune I had although tuner said all the air fuel ratios are all good and at first thought it was the auto, i also thought this however i tried to rev it in neutral and it revs very slow too just like how it runs.

Anyone have any idea wat it is?

I know to drive slow when its cold but yeah this is very slow and realy have to be carefull with traffic sorta slow

Link to comment
https://www.sau.com.au/forums/topic/97020-slugish-cold-start-issue/
Share on other sites

its designed to do this. when the engine is cold (water temp sensor) the ecu retards the timing and adds extra fuel to heat the engine up. during this stage the engine will feel a little flatter and lack response until its heated up. once water temp is around 50deg then its goes to minor level corrections. 80deg is ideal water temp with no correction at all.

also bearing in mind everything else on the car is cold too, diff, gearbox, clutch, bearings etc so its a good thing it lacks response and doesnt come on full stream ahead, prevent bearing / seal excess wear/damage

nah it shouldnt matter how much power it has got. the maps which tell the engine what ign timing and fuel parameters to add for the low load / cruise areas (around 3000rpm ish) wont be any different to your max power tune map areas. the ecu has correction "maps" or settings. these are based on water temp, battery voltage, knock values, air temp (if supported), airflow value and so on.

so based on certain environements the engine is dealt dynamic changes around its environment.

ie when the engine is cold is runs less conservative timing and runs more fuel then when its fully warm. when the engine picks up lots of knock it backs off the timing to protect itself. when the engine detects too much airflow (ie: failed wastegate spring) it protects itself by retarding the timing a lot and dump fuel to richen itself up and try and keep it as safe as possible. when the airflow meter doesnt measure any voltage is does a dynamic rev limit change to 2500rpm. it assumes some air is coming in to allow the engine to run in limp mode but it wont let you rev past, this prevents you from possibly leaning the engine out and causing damage

i also have a rb20det auto R32 and mine does exactly the same thing, very annoying, but once the temp gauge hits the "warmed up" point, you can feel the engine suddenly pick up power. i think the fact we have auto prob "exaggerates" the sluggish feeling.

yeah i just thought it was a bit odd since i have only ever noticed it since tune of the standard computer. Maybe something was fixing in the computer which is why it didn't do it before. Oh well supose ill deal with it. It is a good thing i supose just can't cross the road unless i have a big gap

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
    • It's TWO steering wheels actually. 😛 one for each hand They are wheels, and they steer!
    • Did you even watch the video? Its not a steering wheel. 
×
×
  • Create New...