Jump to content
SAU Community

Microtech Information

claymen

By claymen,
in General Automotive Discussion

 Share

Recommended Posts

claymen Apprentice

claymen

Posted
Posted

Buying a Microtech LT12S but I need to get an air intake temp sensor. What sensor have people used succesfully and where from. I am in WA and would greatly appreciate any help. This is the only thing I havent yet been able to sus out. Ive seen these ecu's run on alot of Skylines so I figured this would be the place to ask.

Link to comment
https://www.sau.com.au/forums/topic/97843-microtech-information/
Share on other sites
claymen Apprentice

claymen

Posted
  • Author
Posted

do you know the model or anthing of it and where I may be able to get one?

aparantly you can use a comodore temp sensor or something. either way I wanna know which one is a good one to get in terms of accuracy and where to get one.

R33S2 Grand Master

R33S2

Posted
Posted

I used a VN como V6 one as recomended by my tuner bought new from holden pretty cheap, got the connector plug from wrecker for nil only trouble was finding thread to match as it is an american thread.(dammed yanks)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • joshuaho96
      Rb26 iron block limit

      By joshuaho96 · Posted

      I was under the impression the reason why OEMs are going with solutions like relatively thin "right-sized" cylinder walls with technologies like PTWA and open deck is because they care a lot about whatever marginal knock margin benefits they get from that vs the structural rigidity benefits of a closed deck block and thicker cylinder walls. I also see some weird stuff like plastic inserts in the water jacket around the cylinders to try and equalize cylinder wall temperatures. re: the PRP blocks and heads at the end of the day it's hard to know what is and isn't going to work there, just have to see what the initial buyers say about it.
    • GTSBoy
      Rb26 iron block limit

      By GTSBoy · Posted

      Which is why I didn't mention that hardness testing, and specifically mentioned the bore and deck thickness testing. Yeah, not really. The bore temperature will be a lot more even around the top half inch or so, where the material distribution is dominated by the deck, and which is the only place where the bore surface temperature heating any gas in the cylinder is likely to have any effect on detonation. Think about it. Another inch or so down the bore, you might have a hotter spot. The gas there might get a bit hotter, then the piston rises squeezes that gas away from there at high speed and mixes it with other gas from nearby. Instant dilution of the problem. I'd be surprised if it was an issue at any time other than in racing engines or OEM dev engines being run at the ragged edge of tuning. Say what now?
    • joshuaho96
      Rb26 iron block limit

      By joshuaho96 · Posted

      https://dsportmag.com/the-tech/education/engine-tech-material-hardness-testing/ The PRP testing on block hardness I'm not sure how much it actually can be trusted. The thinner cylinder walls on RBs is a bit of a problem vs 2JZ but it really depends on the design goal. Siamesed cylinder bores like a 2JZ cause uneven cylinder wall temps too, which means a bit of distortion induced by that + the hotspot can affect knock margin. Something that actually gives me a bit of pause with the PRP block, whether super thick cylinder walls are going to keep it from being drop-in compatible on an otherwise OEM rebuild. 
    • Sleepergm
      Hks race car install

      By Sleepergm · Posted

      Yeah very valid point. I am waiting for one of the other tuners to come back from vacation so he can help me a bit when the cat is installed again. In the meantime I am going to finish up my polishing and ceramic coating that I have started myself.    N45 Dr Beasley product is highly recommended for a paint primer / polisher. Using this EXO Gtechniq also for the ceramic but next time might use the light serum before hand also. Looks great. 
    • joshuaho96
      Hks race car install

      By joshuaho96 · Posted

      Running rich in conditions where it shouldn't probably won't do great things for catalytic converter lifespan. I would fix that sooner than later.
×
×
  • Create New...