Jump to content
SAU Community

Recommended Posts

After having a new deck installed, my a/c in on constant cold. While this is fine for now, ill eventually need heat :P

With the temp either on 18c or 32c, the air is pretty cool. "FH" and "FC" doesnt make a difference, nor does the car running for an 5 minutes or an hour....

As I said, its only come about after having a new deck put in. Are there any sensors round that area that could have come out? Any ideas welcome ;)

Link to comment
https://www.sau.com.au/forums/topic/9814-aircon-not-heating/
Share on other sites

not sure with the 32s but on the 33s there is a sensor in the dash front left of the steering column.

it looks like a little breather vent and has a hose connected on the other side from memory.

If this hose is disconnected (at either end) and is close by to something that generates a little heat, i guess it could make the AC work for colder temps.

check it out... wont hurt

Link to comment
https://www.sau.com.au/forums/topic/9814-aircon-not-heating/#findComment-151906
Share on other sites

Check the sensor near the deck, to the right of it. You may have to pull the deck out (not sure what type you put in there, single or double DIN) two wires and a hose to the sensor. This is the interior temp sensor, mine wasnt connected (actually, wires were cut, damn thieves :( ) and only hot would work. Try look, you never know ;)

Link to comment
https://www.sau.com.au/forums/topic/9814-aircon-not-heating/#findComment-153441
Share on other sites

for now yes...but what about when its cold?

Anyway,

I ripped out the climate control sensor (next to ure left leg) and all works correctly now, bar the climate control. I cleaned the sensor with wd40, hooked it up, no go. So looks like i need a new sensor :(

Any1 have an idea on $?

Link to comment
https://www.sau.com.au/forums/topic/9814-aircon-not-heating/#findComment-153499
Share on other sites

something would have been disturbed around the control area.

the venturi near the clutch pedal draws air from the sencor in the dash to test you can blow through the pipe slowly.also put a rag over the light sencor.

other problems ive had with my passage [same as later mosels]is the hot water sencor reading cold[on the wrong pipe] so the blend door/heater tap motor shuts off to wait for the engine to heat up.a crook thermostate will do this to.to check the door motor will move a little on start up to let a little water through.then close.

my passage R31 climate control freezes up regular to stop this R32 on have a sensor before the evaporator to compare before and after.if these are faulty or dirty it wil go into defrost and go full heat no A/C.

Link to comment
https://www.sau.com.au/forums/topic/9814-aircon-not-heating/#findComment-153596
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That looks good, but I think you're going to need much beefier side skirts now.
    • They are daft and there's a reason it never caught on. Steering feel? We don't need no stinking steering feel!
    • I gotta pull you up on this. It's driving me crazy. A shutter is something that closes, like over a window or in a cmera. The word you want is shudder. That LSD is clearly f**ked. Take it to a diff shop and get it disassembled and examined by an expert. YOu might have plates welded together or something equally crazy.
    • Define "starting to fail". Wy not just rebuild them?
    • Check the Nistune doco. There are a few assumptions being made here that might not be valid. I will list the things that occur to me: Base map. Base map for what? Base map for Z32? Then the cranking pulse width is probably wrong for an RB25. The extra 500cc of capacity might well be enough to prevent it from catching. Base map for RB25? I don't think you can load one of those into a Z32. You have to just make the settings correct for an RB25 in the Z32 base map. That is either K or the TIM to get the pulsewidth right. Loom. You bought a loom for an RB. And you plugged it into a Z32 ECU. Did you make sure that any iwre differences were swapped. From memory, there's at least a couple. And as per the others, I would suggest making sure that the fuel pressure is correct while cranking and that the injectors are actually flowing as expected. They really must come out and go on the bench, unless you do find that you have messed up as per above points. I would also suggest watching in Nistune to make sure that everything is reading correctly. That the correct binary flags are raised at the right time (like the crank signal), that there's no stupid values in K or TIM. That you have not got mismatched firmware for the ECU and/or a wrong image loaded.
×
×
  • Create New...