Jump to content
SAU Community

Recommended Posts

simple answer F*CKIN HARD

i dont agree with engine out would make it sh*t loads easier though just seems like an AWFUL lot of work to take out the engine just for oil filter change

it is possible to change without removing engine but it is a absolute bitch!!! i changed mine with the engine in BUT i did have the plenum off at the time and it was still a mongrel

i recommend get a oil filter relocation kit ASAP

RellikZephyr

Link to comment
https://www.sau.com.au/forums/topic/98167-oil-pump/#findComment-1783451
Share on other sites

simple answer  F*CKIN HARD

i dont agree with engine out    would make it sh*t loads easier though  just seems like an AWFUL lot of work to take out the engine  just for oil filter change

it is possible to change without removing engine  but it is a absolute bitch!!!  i changed mine  with the engine in  BUT  i did have the plenum off at the time  and it was still a mongrel

i recommend get a oil filter relocation kit ASAP

RellikZephyr

are you kidding mate? changing the oil filter is not hard at all. you read wrong mate, wrxhoon was talking about the oil pump

you seriously think you have to remove the plenum, or engine to change the oil filter?? hehehe

yes there are easier cars out there, but it's not a plenum off or engine out job by any means. god damn that's funny.

Link to comment
https://www.sau.com.au/forums/topic/98167-oil-pump/#findComment-1783496
Share on other sites

are you kidding mate? changing the oil filter is not hard at all. you read wrong mate, wrxhoon was talking about the oil pump

you seriously think you have to remove the plenum, or engine to change the oil filter?? hehehe

yes there are easier cars out there, but it's not a plenum off or engine out job by any means. god damn that's funny.

You tell him Richard , they are not that bad to work on , i dont even spill the oil when i change the oil filter ( with engine in place i may add) .

The oil pump is doable on the car as well but by the time you stuff around and take the xmember off , its just as easy to pull the donk out . Then again why would you want to change the oil pump ? If its because it failed what makes you think the donk is still ok ? In my view a failed oil pump means engine out and full rebuild job .

Link to comment
https://www.sau.com.au/forums/topic/98167-oil-pump/#findComment-1784115
Share on other sites

ahh Oil PUMP sorry my bad

but you think changing oil filter is easy??

i took my plenum off for different reason and changed oil filter while i was there

no i dont think filter is a engine out or plenum off job thats why i thought it was strange and a bit extreme

well i feel like a bit of a idiot now :)

ok im gonna go hide for like a week and not post and hope you all forget what i said

RellikZephyr

Link to comment
https://www.sau.com.au/forums/topic/98167-oil-pump/#findComment-1786210
Share on other sites

I love customer diagnosed complaints. Guy rings me last week and says...'My diff filler plug is missing, can I bring it in to have it replaced?' I tell him sure thing. He get's in, driving a barina. Tells me that the diff in the back has it's filler plug missing. I assure him that they don't have a diff in the back coz it's a front wheel drive. He proceeds to crouch down and point at the lump in the floor pan with a threaded hole in the base (jacking point).

When you have a problem, ask what it could be and explain the symptoms. It is easier to get the correct response that way.

Link to comment
https://www.sau.com.au/forums/topic/98167-oil-pump/#findComment-1791608
Share on other sites

I love customer diagnosed complaints. Guy rings me last week and says...'My diff filler plug is missing, can I bring it in to have it replaced?' I tell him sure thing. He get's in, driving a barina. Tells me that the diff in the back has it's filler plug missing. I assure him that they don't have a diff in the back coz it's a front wheel drive. He proceeds to crouch down and point at the lump in the floor pan with a threaded hole in the base (jacking point).

When you have a problem, ask what it could be and explain the symptoms. It is easier to get the correct response that way.

No offence mate, sometimes a salesman or a mechanic, WITHOUT looking at the problem, think they have a fair idea about whats wrong. In which in this case I was confidently told that it could be the oil pump. And hence, I have posted what could be the problem and so far I have recieve excellent feedback to question.

There is your customer diagnosis.

More over I wanted to direct the question in a way so that the community can visualise the problem without having to ask more questions about where the problem lies. Some may call it logical progression.

BTW. thats pretty funny story about the barina.

-Arbess

Link to comment
https://www.sau.com.au/forums/topic/98167-oil-pump/#findComment-1793077
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...