Jump to content
SAU Community

Recommended Posts

  • Replies 190
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Stolen! It has never been registered!! It just got off a boat from Japan and it couldn't get on that boat if it was stolen (de-registration papers) so yes, waste of time!

Nice work RTA!

Agreed!

all did not go well on tuesday...however, i put in the 500HP fuel pump, and am putting the new platinum spark plugs in tomorrow morning. if all goes well, it will be rego'd on monday

CAR IS RUNNING!!!

fuel pump was almost dead ie not flowing enough,

and the major problem was a relay on the ignition coil circuit decided to croak it.

...makes it hard to diagnose the problem without a wiring diagram.

but the most important part of all is... its all systems go for rego on monday!

i put the walbro 255L/hr pump in, it was similar to the factory pump other than the one end which had the hose and the plug positions swapped around.

still managed to secure all of the clips in the cradle it sits in, other than one of them.

yeah car is registered, and constantly being driven :D

i sure am going through a lot of fuel... ill let everyone know how many k's i get out of the first tank in the petrol thread.

my stagea no longer has a camo front bar :):):)

ill change the pic in my signature whenever i get around to it :P

i picked it up yesterday from the smash repairers.

i also forwarded both of the invoices for repair/painting of my front bar to KIPS and i got an email back saying that they will pay me next week WOOHOO!!!!

  • 1 month later...

well its taken ages but i finally got the money from the insurance claim through KIPS today, i was beginning to get a bit worried for a while there, i didnt want to have to cop the $900 repair bill.

God Damn - Im so stoked that I havent had ANY troubles whatsoever with my Stagea (well, besides dills drilling into my wiring loom when the cdstacker was installed under the passeneger front seat).

touch wood hey! :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...