Jump to content
SAU Community

Recommended Posts

well what can i say

summary of what goes down on a fatz drift day (high res)

yea baby

http://www.clutchfcukers.com/videos/Fatz.D...ivX6.1-KERO.avi -47Mb

and the ones everyone wants to see

88sillo ripping some monstor burnouts (rb30 power!!!!!!!!!!)

http://www.clutchfcukers.com/videos/Mark.B...ivX6.1-KERO.avi -13Mb

http://www.clutchfcukers.com/videos/Mark.B...ivX6.1-KERO.avi -11Mb

after seeing marks burnout mine sucks but here it is

http://www.clutchfcukers.com/videos/Fatz.B...ivX6.1-KERO.avi

Link to comment
https://www.sau.com.au/forums/topic/99277-fatz-drift-day-vids/
Share on other sites

yeh dude wiill be there at 5pm onwards

assuming i dont get pulled over by cops on my way there...and if that does happen, then just keep ur eye out for a guy on the side of the m7, lubing his ring up whilst leaning over his bonnet with a police officer standing nearby..

cubes ill dig around and try to find the dyno sheet

buggered if i know where it is though

basically was on full by 2000rpm. flat curve all thbge way from 2000rpm onwards. torquey motherf**ker. tis a prick on the tyre bill though. 237rwkw @ 10psi

Looks to be my kind of turbo...

Hows it rev? Noses over after 5500rpm or holds strong to what max rev's?? :D

I'm curious on your setup... Its holding those high rev's well without breaking oil pumps.... :D

8cm turbine housing I assume?

I'm sure you've heard it before.. but shiet... you can swing that 31 around unbelievably. Awesome.

Edited by Cubes
Looks to be my kind of turbo...

Hows it rev? Noses over after 5500rpm or holds strong to what max rev's?? :)

I'm curious on your setup... Its holding those high rev's well without breaking oil pumps.... :D

8cm turbine housing I assume?

I'm sure you've heard it before.. but shiet... you can swing that 31 around unbelievably. Awesome.

stock rb30e bottom end and just very mildly ported head. i recommend this turbo combo.

revs well i usually head right up to limit ie - 7200rpm - and it keeps pulling right up until 7200

dunno what turbine housing but 8cm sounds good.

setup is basic

rb30e bottom end

rb25 head mildly ported

trust manifold (brandname crap)

550cc injectors

td06-20g

power fc

tuned to 10psi = 237rwkw

os giken triple plate clutch

fuel reg

fuel pump

thats about itr mate - i chucked up some pics for you to see it.

18v0262.JPG

18v0263.JPG

18v02ax.JPG

18v02ay.JPG

18v02bq.JPG

would like to say that it is me doing the burnouts but it is in fact glen hunter who built the car

i'm giving it a shoit tomorrow night (have done burnouts in it before but this will be my first big one) at wsid in burnout comp. should be amusing.

anyway have a good one. get drunkj!!

Awesome...

10psi for any reason? Not much more left in the std injectors or she was pinging?

Good luck with the burnouts... you'll have to work hard your builder is definitely awesome.

Have a good new year. :)

Edited by Cubes

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...