Jump to content
SAU Community

Recommended Posts

Item: Genuine HKS intercooler

Location: Brisbane

Website:

Item Condition: Good Condition

Reason for Selling: Due to upgrade

Price and Payment Conditions: 200+postage

Extra Info: intercooler core size is 400x270x70 overall with end tanks is 530mm

Pictures: can be suppied

Item: Garrett GT30Ball Bearing Turbo 550hp

Location: Brisbane

Website:

Item Condition: as new Condition

Reason for Selling: Due to upgrade

Price and Payment Conditions: 1800+postage

Extra Info: .70 front polished housing, .82 rear, t3 flange, can sell with heat bag for an extra $150, turbo has only done 500km

Pictures: can be suppied

Contact Details: [email protected] or call 0418156085

post-14595-1135406597.jpg

post-14595-1135406626.jpg

post-14595-1135406653.jpg

post-14595-1135406684.jpg

post-14595-1135406720.jpg

Edited by ilum4eva
aint these turbos 1800 new? correct me if im wrong

if so id like 2 know what the new price will be? may be interested.. ;)

  • 2 weeks later...
  • 3 weeks later...

The hks intercooler has been sold. The new price for the turbo is $1800 which now includes postage, the heat bag, a new exhaust gasket, t3 turbo gasket and the turbo of course that's more than $2500 in value for $1800. I also have forsale is a rising rate malpassi with a gauge that's only done 10hrs work. I'm asking 150 plus postage.

pls e-mail me with any further questions at

[email protected]

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...