Jump to content
SAU Community

Recommended Posts

hey all, i have bought a n/a r33 through an importer in sydney and due to pick the car u soon today i sent an nrma inspector to check the car out

relly dissapointed the car has some guard damage some interior damage some exterior panel damage some under enginge damage which could effect oil pressure , knocking sound which is caused by some spring in the engine TELL ME THIS ISNT THAT BAD considering that i have spoken to the dealer and he said everything will be fixed and car will undergo detailing . is this normal in a way considering it has been on a boat , through customs and down from queensland p.s im getting the car for 12000 thanx !!!

post-25629-1135922311.jpg

Link to comment
https://www.sau.com.au/forums/topic/100121-r33-na-damage/
Share on other sites

i wudn't touch it....

skylines are much much cheaper now... about 2 years ago (bit less) when i got my R33 GTS25 it cost me a good odd 16k.

1994 R33 GTS25 with 65000km with log books and all.

back then the supply was low with the high demand, and the expensive compliance plates (at that time about 5k)

now you have a much larger range and choices to choose from, if you dont like it and uncomfortable with it... just walk away.

eug

Link to comment
https://www.sau.com.au/forums/topic/100121-r33-na-damage/#findComment-1825439
Share on other sites

walk away from it, it sounds dodgy. for 12k you get an NA in aus. it may not have the rims and bodykit but it also wont be damaged. but the decison is up to you, if the dealer is going to fix it most likely they will do a dodgy repair, and then when it comes time to sell it, you will have troubles.

Link to comment
https://www.sau.com.au/forums/topic/100121-r33-na-damage/#findComment-1826458
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
×
×
  • Create New...