Jump to content
SAU Community

Pbr Slave Cylinder Part Number?

predator

By predator,
in General Maintenance

 Share

Recommended Posts

predator Grand Master

predator

Posted
Posted

Does anybody have the box, etc lying around and know the part number for the RB20DET slave cylinder?

I went to repco today, and they were not sure of the exact one, even though they had some close guesses. Anybody know for sure?

I believe its PBR brand.

Link to comment
https://www.sau.com.au/forums/topic/100459-pbr-slave-cylinder-part-number/
Share on other sites
Cubes Grand Master

Cubes

Posted
Posted (edited)

PBR don't do one for the R32 as far as I'm aware..

Its another brand..

I replaced mine, slave w around $40, the master cyl was $75 or there abouts. I will try and find the pics I took of the part number(s).

I think I listed the part numbers in an SA thread I made a while back.

Edited by Cubes
predator Grand Master

predator

Posted
  • Author
Posted

Called the distributor (IBS not PBR), and they pointed me in the direction of a stockist in my area.

IBS-JB4215 was the part number which was compatible with my old one..

http://www.indbrake.com.au/ -- call for distributors in your state.

Cost was $33 ;) Can't beat that for a brand new unit.

You will need to use your existing 'pin' out of the old one, or you should be able to easily find something else suitable.

Cubes Grand Master

Cubes

Posted
Posted (edited)

Remove the center box while your replacing the master cylinder.

Bend the line from the master cyl back on its self so it connects directly to the rubber slave cyl line.

I found pedal feel to be much better with a ceramic clutch, I am now able to slip it and have more control over fine movements.

Prior it felt I was a blind man. :P

Bleeding is also much easier.

Edited by Cubes
  • 11 months later...
eXc Mentor

eXc

Posted
Posted
Called the distributor (IBS not PBR), and they pointed me in the direction of a stockist in my area.

IBS-JB4215 was the part number which was compatible with my old one..

http://www.indbrake.com.au/ -- call for distributors in your state.

Cost was $33 :/ Can't beat that for a brand new unit.

You will need to use your existing 'pin' out of the old one, or you should be able to easily find something else suitable.

Just thought I'd confirm this is the correct part number, I got one today. R32 GTST Slave cylinder...

95SKY Community Regular

95SKY

Posted
Posted
Called the distributor (IBS not PBR), and they pointed me in the direction of a stockist in my area.

IBS-JB4215 was the part number which was compatible with my old one..

http://www.indbrake.com.au/ -- call for distributors in your state.

Cost was $33 :( Can't beat that for a brand new unit.

You will need to use your existing 'pin' out of the old one, or you should be able to easily find something else suitable.

Maybe try JB4215 for PBR?? Just a idea??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • iain_ST44GA
      M35 VQ25DET starter motor

      By iain_ST44GA · Posted

      Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • Murray_Calavera
      R33 GTR running -9 with no tune

      By Murray_Calavera · Posted

      I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...