Jump to content
SAU Community

Hid

eric_cheung_

By eric_cheung_,
in Queensland

 Share

Recommended Posts

Silver_R34_GT-T Grand Master

Silver_R34_GT-T

Posted
Posted (edited)

they arer legal as long as u dont go over 6000K, anything below is ok.

My r34 GTT has HID in it, im looking to upgrade to those 8000K or somethin higher, cept the price and the illegal part scares me off.

Edited by Silver_R34_GT-T
Link to comment
https://www.sau.com.au/forums/topic/100928-hid/#findComment-1843564
Share on other sites
jake32 Mentor

jake32

Posted
Posted
hi guys

as far as i know they are still not legal as they are non adjustable!!! Wierd cause an r34 GTR head lights are adjustable yet you still have to take them off to get them complianced another contradiction in QLD Transport rulings.

cheers

they need to be self leveling and have washers to be compliant,interior adjuster for load is not enough,if 34`s had same set up as honda,bmw,volvo etc ...self leveling device in boot and h/light washers they would comply.Thats ADR rules.. nothing to do with qld transport really,not sure if they would know difference between self leveling and non adjustable though once the car is registered: :(

Link to comment
https://www.sau.com.au/forums/topic/100928-hid/#findComment-1843609
Share on other sites
jake32 Mentor

jake32

Posted
Posted
can someone explain to me what self leveling n have washers mean??

does it mean the bulbs move as the car goes up or down a hill. n also the bulbs wash themselves? wtf?

if you ever noticed oncoming bmw etc you will see xenon h/lights "changing colour" type thing as they approach...this is lamp adjusting to roadsurface ..leveling,

the washers are the same as windscreen washers but mounted in bar and face the h/lights for cleaning

Link to comment
https://www.sau.com.au/forums/topic/100928-hid/#findComment-1844893
Share on other sites
n15m0 Grand Master

n15m0

Posted
Posted
ahh ok, but y do HID need the washers and normal lights dont?

Correct me if i'm wrong but this was what i was told, when headlamps equipped with HID are dirty they do not give out as much light hence poorer visibility, compared to normal halogens.

Link to comment
https://www.sau.com.au/forums/topic/100928-hid/#findComment-1845719
Share on other sites
53XYN Veteran

53XYN

Posted
Posted

humm thats not really correct.. the plastic lens / glass gets discoloured because people use high temperature globes / cheap hid's that dont have UV cut in them.. hense the discolouration... you can polish 80% of it out using meguires plastic X polish and cleaner.or brasso if you have the time.. . i have hid in my 33 both of them gtr n gtst .. ones 6500K the other is 8000K have been pulled over many times but they never mentioned the light ,im not saying they are legal.. depends on cops decresion

Link to comment
https://www.sau.com.au/forums/topic/100928-hid/#findComment-1849624
Share on other sites
eric_cheung_ Enthusiast

eric_cheung_

Posted
  • Author
Posted

thx for all reply and suggestion! as you guys already know that the HID is very bright light specially at the night (skyline + HID = eyes catcher ), so I have a little bit worries after I put the HID in my car, the cops will always say "hi" to me on the road.... :(

Link to comment
https://www.sau.com.au/forums/topic/100928-hid/#findComment-1854298
Share on other sites
gexenon Collaborator

gexenon

Posted
Posted

We sell GE HIDs to many companies and have never had a problem with Legality.

Officially, ADR requires Auto leveling and headlamp washers fitted for HIDs.

Auto leveling adjusts the level of headlight depending on number of passengers (as passengers at the back lifts the front of the car). They do not level as the car drives along. They reason why BMWs change colour is due to the projector they use. (its like a rainbow effect, light coming from the side of the projector has the shortest wave length hence blue)

Washers are used to keep headlight free from ice. As you can imaging, snow and ice and reflect alot of light and this can cause HIDs to be "glary".

ADRs regarding HIDs are copied directly from the european ECE 37 regulations. In Europe, some counties do have lots of snow and hence the washers, however, they are useless in most parts of Australia.

In US and JAP, HIDs don't need to be self leveling or washers. However, this is soon to change.

Link to comment
https://www.sau.com.au/forums/topic/100928-hid/#findComment-1867116
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • wizlb
      Who has a Infiniti Q60, Q50 (V37)?

      By wizlb · Posted

      I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Kinkstaah
      Starting again

      By Kinkstaah · Posted

      Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...