Jump to content
SAU Community

Recommended Posts

  • Replies 71
  • Created
  • Last Reply

Top Posters In This Topic

If we need a minimum of 6 cars, and this is a "bling" event, id suggest that we first use the sort of skylines that Autosalon aims at ("blinging")

Ill have a new interior by then also, its white suede with grey leather

Cant be hard to get 6 good looking skylines

Would also be good to get a variety, R32 R33 R34 gtst's and gtrs

Either way, im in

If we need a minimum of 6 cars, and this is a "bling" event, id suggest that we first use the sort of skylines that Autosalon aims at ("blinging")

Ill have a new interior by then also, its white suede with grey leather

Cant be hard to get 6 good looking skylines

Would also be good to get a variety, R32 R33 R34 gtst's and gtrs

Either way, im in

Not a bad idea....

but poor Mr Stagea :O

Hey Jago. just a quick question. How long is that inlet system you have?is that custom?

everything is custom mate, no kits for the 31, for anything really (or are hard to come by and expensive)

As for autosalon, i wouldn't mind goin, just gotta fix up some paint tho, it aint 100% show grade but hey, it's different

:)

Where have you been @ phil.

Whats going on with the car.

yea i just been here and there mate, haven't seen you around much either :(

As for the car, just came out of the workshop, fixing a heater hose, which caused major overheating. High pressure hose power steering leak, screwed sump plug, fitted bigger injectors, upped the boost and dyno tuned the microtech. Ran 182rwkw on the autosport engineering dyno @ 13psi, peak power at 7000rpm ;)

What bout u man? or u keep her the same? nice lookin 33 i must say

Man this seems to be getting serious... Definitely count ME in!!!!!!!

After all.. I'm probably teh biggest RICER in here...

BLING.. check

PAINTWORK.. check

LED underbody and interior.. check

AND

NO IMPULS.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
×
×
  • Create New...