Jump to content
SAU Community

Recommended Posts

Hi Guys,

I am building up a Series 1 RB25DET that i bought to put into my Datsun 240k. I am looking to buy the Nissan VRS kit or the full nissan kit (as i will eventually do an RB30DET conversion).

I want to ring up nissan tomorrow to order a kit, but this is going to be difficult because i don't have a corresponding VIN number i can give them.

does anybody know for sure what the nissan part numbers for both the VRS kit is and also the full kit for the Series 1 RB25DET (Manual)

and if failing that, would anybody with a Series 1 GTST mind PM'ing me their VIN number so i can order the correct parts from nissan tommorrow?

is there a difference between S1 and S2 kits?

thanks

Kent

and the full kit part number is 10101-17U26 RB25DET Gasket Kit - Engine Repair

it contains:

1x Gasket goo (150g)

1x drain plug washer

1x cylinder head gasket

1x crankshaft rear oil seal

24x valve stem oil seal

1x rocker cover exhaust gasket

1x rocker cover intake gasket

2x camshaft oil seal

1x crankshaft oil seal

1x intake manifold collector gasket

1x manifold gasket

1x exhaust manifold gasket

1x oil strainer gasket

1x oil pump gasket

1x throttle chamber gasket

1x soeal o ring

1x AAC valve gasket

and the full kit part number is 10101-17U26 RB25DET Gasket Kit - Engine Repair

it contains:

1x Gasket goo (150g)

1x drain plug washer

1x cylinder head gasket

1x crankshaft rear oil seal

24x valve stem oil seal

1x rocker cover exhaust gasket

1x rocker cover intake gasket

2x camshaft oil seal

1x crankshaft oil seal

1x intake manifold collector gasket

1x manifold gasket

1x exhaust manifold gasket

1x oil strainer gasket

1x oil pump gasket

1x throttle chamber gasket

1x soeal o ring

1x AAC valve gasket

What did that end up costing?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It's almost certainly a reluctor generating an "AC" waveform. No, ECUs don't generally read those - they're usually set up for PWM square wave 0-5v stuff.
    • Working through possible solutions of converting my mechanical speedo.    Anyone know what type of speedo sensor the factory r34 gtr getrag has ? what the output is ? I assume its not a VSS and more a voltage like earlier speedo sensors ? Can an ECU read it ?  
    • roof rail delete used to be a thing, they were made locally for a while too
    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
×
×
  • Create New...