Jump to content
SAU Community

Recommended Posts

COST: $25 / person

FORMAT OF DAY

9:00 - Briefing, at which all participants need to attend.

Sessions will alternate between DRIVER ONLY and PASSENGER Sessions.

Each Session will run for approx 30 minutes.

REQUIREMENTS:- You will require a Australian Standard approved helmet.

- Be covered from wrist to neck to ankle in a flame retardant material clothing.

- Suitable closed in footware.

THE CAR:

- Needs to be of a roadworthy or race worthy condition and have all lose objects removed from the car.

- All brake lights should be working as there are a number of cars on the circuit sometimes of different capabilities therefore brake lights are important to warn participants behind that you are stopping.

LICENCE REQUIREMENTS:

There are no licences required for the day but drivers need to be over the age of 16, but this would depend on the stature and capabilities of the person involved. Passengers may be younger than sixteen but must be able to fit into the vehicle in a safer manner.

OTHER:

- There is air available for tyres but you will need your own pressure gauge or borrow someone’s on the day.

- Fuel will be available, AVGAS, ULP, OPTIMAX and JFP Racing Unleaded at selected times through the day.

- The kiosk will be open and will have hot and cold food and drinks available.

If you have not been to a Winton Fun Day and are interested in participating in motorsport or a least seeing what all the fuss is about the you should mark January 29th in your calendar as a fun day for the whole family.

For more details contact Winton Motor Raceway on (03) 5766 4235.

Link to comment
https://www.sau.com.au/forums/topic/101775-winton-fun-day-sun-29-jan-2006/
Share on other sites

sound cool

does this mean around the track

YEP....I went to the last one in december.....its OK and good fun but you gotta be careful as theres a lot of idots who act really stupid on the track

heros

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...