Jump to content
SAU Community

Recommended Posts

Hey guys,

I have recently set a power goal of 200 rwkw for my RB20DET R32. At the moment I have between 160rwkw and 170rwkw. The mods I have are:

3inch Exhaust

ZG30 Turbo

Boost controller running 12 - 14 psi

No A/M ECU yet. Looking at the Power FC.

Besides from a FMIC, what mods should I look at for squeezing out an extra 40kw at the wheels?

Link to comment
https://www.sau.com.au/forums/topic/101782-200rwkw/
Share on other sites

remapped ecu, good cold air intake, fuel pump, 3" split dump and get it tuned. i dont think you will make 200 however

What paulr33 said.

#But your 3'' xorst will still be ok as long as it is 3'' from the turbo back.

#Hi flow air filter.

#Remapped ecus are allright.But if you have the money get a pfc.

#Maybee a adj fpr.Becuase at high injector duty you will want constant high pressure in teh fuel rail.I was told this by CRD.

#A hi flow rb20 or 25 turbo and you will make over 200rwkw.

Other than that teh stock turbo wont push beyond 180-190rwkw that easily.You do need all of these,though,if you want to get the max! out of your current setup.You need an upgrade on the turbo.

As you would have allready seen though dynos are conservative to say the least.With many saying their car has 200+rwkw on the stock turbo.When i was at CRD my r33 was tuned to 182rwkw stock turbo with a 2.75'' dump,stock cat and 3.5'' xorst from then on.With all the usual other mods.

I hope your not running 14psi in the heat of the day with that tiny intercooler.After the powah look at the suspension if you havent allready.Then take it to the track and thrash it!!

I am at the point now where i can upgrade the turbo and easily make 220rwkw.

HTH... ;)

Link to comment
https://www.sau.com.au/forums/topic/101782-200rwkw/#findComment-1866474
Share on other sites

Ill also get it tuned on Shell Optimax Extreme and see how that goes.

Is that the 100ron stuff? If so i heard it wasnt good for skylines, apparently it only works well in new cars.

I havent tried it though, i just stick with my BP Ultimate.

Link to comment
https://www.sau.com.au/forums/topic/101782-200rwkw/#findComment-1867113
Share on other sites

  • 2 weeks later...

Just an update. I have installed a FMIC and an apex'i power intake. It actually made alot more of a difference than I expected it to! Its alot louder now too:). I am almost ready to order a PowerFC for it. Any suggestions where the best place for one is?

Link to comment
https://www.sau.com.au/forums/topic/101782-200rwkw/#findComment-1904055
Share on other sites

hey dude, ive got a 4dr 32 aswell and i made 170rwkw with rb25 turbo, gtr fuel pump, 1bar boost, 3" turbo back exhaust, and shitty hks mushroom pod

no front mount... its on the way though and itll be in the car soon

my point is... get an aftermarket dump pipe!

they do HEAPS

go look at your stocker and youll see that the bit where the wastegate opens goes into a "wall" in the dump pipe... VERY bad design, causes a SH*TLOAD of turbulance when the wastegate opens and makes exhaust gases flow really sh*tty.

also, i assume that by ZG30 turbo, you meant VG30 out of a 300ZX.

if this is the case, go get that hi-flowed.

many people have had good results with hi-flowing that turbo because of its decently large exhaust housing

PS: GET THAT DUMP PIPE!!!

Edited by salad
Link to comment
https://www.sau.com.au/forums/topic/101782-200rwkw/#findComment-1904961
Share on other sites

You may want to figure if the VG30 turbo you have is the steel wheeled version. As you should be able to run 18+psi fairly reliably. And with other sensible mods Such as a Good quality split front/dump, Quality cat (a metal one), GT-R injectors, Regulator and PFC or remap there is no reason why you can't comfortably surpass the 200rwkw figure.

Oh and finding a PFC for a 32 can be difficult. "AP Engineering" make em.. don't know why.

This is why so many 32 owners opt for the remap instead. Wich can net very healthy results if performed correctly.

Good luck anyway :P

Edited by Drift_Limo
Link to comment
https://www.sau.com.au/forums/topic/101782-200rwkw/#findComment-1905506
Share on other sites

sure r u? have you driven one? big call if you havent.

imo most remaps are just stock tune with fc and speed limiter removed

a remaped ecu(tune by Adelaides Guru) and just a stock wt fcd comp were both tested out on Huddys car both power curves were exactly the same?

oh and VG30 turbo's never came with steel rear wheel from the factory.

Edited by 1400r
Link to comment
https://www.sau.com.au/forums/topic/101782-200rwkw/#findComment-1907651
Share on other sites

AS everyone else has mentioned:

FMIC (which you have now)

Apexi air filter (whic you have now)

3" dump all the way through (with a "CUSTOM" cat :D )

PFC is the way to go if you can afford it but there is nothing wrong with getting a ECU remap by someone like Dr Drift, Sams results kinda speak for themselves!!!!

If you want info on the "CHEAPEST" AP Engineered Power FC then PM :)

Other than that good luck with your power figure and hope you get what your looking for...

Cheers B

Link to comment
https://www.sau.com.au/forums/topic/101782-200rwkw/#findComment-1907776
Share on other sites

check out huddys thread in the ceffy section

mods needed

fuel pump

exhaust

fcd

2530 or similar

front mount

boost required 1 bar

result 215 rwkw

That sounds like alot, I have fuel pump, 3inch exhaust/dump pipe, gtr injectors, wolf 3d, cooler, and 1bar and Im making 160rwkw, altho my turbo is still stock.

Link to comment
https://www.sau.com.au/forums/topic/101782-200rwkw/#findComment-1910154
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
×
×
  • Create New...