Jump to content
SAU Community

Recommended Posts

Item: R32 GTSt Front Seats

Item Condition: Mint, You will not find better! (No Marks, Rips, Cig burns)

Reason for Selling: Upgraded

Price and Payment Conditions: $180 for the Pair

Item: R32 Carbon Fibre front strut/tower bar

Item Condition: Good (some rubbing on underside of bar, this cannot be seen when on the car, and will not effect performance)

Reason for Selling: Would not fit under my Carbon bonnet.

Price and Payment Conditions: $60

Item: Interior Trim Panels

Item Condition: Good (trim on rear seat panels is starting to come away, and needs to be glued back on). No Stains, Cig burns etc.

Reason for Selling: Upgraded

Price and Payment Conditions: $40 for the set of 4

Item: R32 GTSt Fuel Pump

Item Condition: Perfect working condition.

Reason for Selling: Upgraded

Price and Payment Conditions: $20

Location: All items are located in Nowra (2 hours drive south of Sydney)

Contact Details: PM or phone 0414792608

post-3204-1137294678.jpg

post-3204-1137295163.jpg

post-3204-1137295240.jpg

post-3204-1137295324.jpg

post-3204-1137306766.jpg

post-3204-1137306903.jpg

post-3204-1137307043.jpg

Edited by Ryno
Link to comment
https://www.sau.com.au/forums/topic/101900-r32r33-parts/
Share on other sites

Item: R32 GTSt Front Seats

Item Condition: Mint (No Marks, Rips, Cig burns)

Reason for Selling: Upgraded

Price and Payment Conditions: $200

Item: R32 GTSt Rear Seats

Item Condition: No Marks, Rips, Cig burns, however Top of seat has sun fading.

Reason for Selling: Upgraded

Price and Payment Conditions: $50

Item: 3" Hi Flow Cat (Xforce Stainless Steel)

Item Condition: Excellent (Used for only 2 months)

Reason for Selling: Upgraded to 4" Magic Cat

Price and Payment Conditions: $80  Payment pending

Item: 3" Cat replacement pipe/Resonator

Item Condition: New

Reason for Selling: Not needed

Price and Payment Conditions: $50

Item: R32 Carbon Fibre front strut/tower bar

Item Condition: Good (some rubbing on underside of bar, this cannot be seen when on the car, and will not effect performance)

Reason for Selling: Would not fit under my Carbon bonnet.

Price and Payment Conditions: $100

Item: R32 Adjustable Pillowball Rear Camber Arms and Traction Rods.

Item Condition: Brand new, Excellent Quality

Reason for Selling: Not needed

Price and Payment Conditions: $200 for the set of 4

I also have all interior trim panels available (to match the seats), plus the window surrounds available.

Location: All items are located in Nowra (2 hours drive south of Sydney)

Contact Details: PM or phone 0414792608

pics of pillow balls and interier trim plz and prices

Link to comment
https://www.sau.com.au/forums/topic/101900-r32r33-parts/#findComment-1867432
Share on other sites

Will those subframe bushes fit a S13?
Yes they will, I believe they fit:

R32, R33, S13, S14, 300ZX

Ok mate,

Consider them sold.. If u still have them that is..

Are u willing to take $70 delivered? I'm in QLD.. postcode:4300

Pm me with your account details.. or if ur willing to do COD that'd be great..

Link to comment
https://www.sau.com.au/forums/topic/101900-r32r33-parts/#findComment-1923123
Share on other sites

the door trims, mainly interested in passenger door  trim but would take them all , whats the comdition of that trim panel?

Thanks

Hey mate,

The passenger side door trim is perfect, with the exception of this area, which I have had repaired. Because it is on the bottom of the trim (near the speaker) it is hardly noticeable.

Cheers, Ryan

post-3204-1139308868.jpg

Link to comment
https://www.sau.com.au/forums/topic/101900-r32r33-parts/#findComment-1930929
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • It's been quite the ordeal but hey, at least you figured it out.
    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...