Jump to content
SAU Community

Recommended Posts

Tried the search thing. Hope its OK to post here. Bought the R 31 with a dud front drivers door. Entry had to be from the passenger side and then open the inner latch to get door open. So far so good. :wub:

Had the car a couple of weeks and driving it everyday because my motorbike was in the shop. In the Woolies car park and get back to car, passenger door won't open. Nob thing tries to go up with key turn but something stops it and door won't open. :wub:

Stinking hot, try for 45 minutes, boot open, jack out, quarter window driver's side smashed to gain entry. :P Tough glass eh.

Next day off I'll be removing the inner cover to attempt to fix drivers side door, however the passenger door inner latch no longer works so door permanently locked. :D:)

So:

Can anyone direct me to a thread anywhere in the world that will assist me to fix drivers door and is there an alternative to a lump hammer and angle grinder and massive freak out to fix the passenger door. I'm not game to replace the quarter window in case I have to smash it again. Car is an 88 GXE 3.0 (Series 2?)

Link to comment
https://www.sau.com.au/forums/topic/101926-help-r31-doors-freaking-me-out/
Share on other sites

best idea krusty, is to pull the front seat out, then try get the door card off. The rods in the door have more then likely come off or jammed, if they're jammed just try given em a good yank (MAKE SURE U PUT A RAG ON THE DOOR BEHIND WHERE U HAVE YOUR HAND, U WILL GET DEEP CUTS IF U DON"T), if the rods have just come off just go to a wreckers & get some more rod clips. If the locks are jamming up might be an idea to get some 2nd hand door locks @ the same time.

Just ask the wreckers if u can have the full set of locks with the keys...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...