Jump to content
SAU Community

Recommended Posts

My clock doesn't work at all (doesn't light up) and my climate control keeps forgetting what it was last set to and starts at 25 every morning. I checked all the fuses under the dash - had two blown but neither fixed it (f**k knows what else has been broken lol, I haven't noticed anything).

Anyway, I noticed the A/C fuse is a large one under the hood. I don't spose it's shared by the clock?? I haven't had time to check the fuses under the hood yet, but it wouldn't surprise me... I'm hoping this is the simple answer and that fuse just needs replacing. Otherwise, all my fuses are fine and I have a larger problem :D

Another thing: I've sometimes got the *clack clack clack* noise when the A/C comes on cos of the dodgy actuator/ louvre mechanism slipping. Is there any chance that problem could have caused the fuse to go (if, indeed it's gone)? And hence I need to solve it to stop the fuse from blowing again? Just a thought..

Link to comment
https://www.sau.com.au/forums/topic/102530-r33-ac-clock-share-same-fuse/
Share on other sites

My actuator thing makes that noise, but it doesn't affect my clock or A/C. Everything works perfectly but I wouldn't mind knowing what to do to get rid of that noise!

You might want to check the wiring to the back of the dash panel. If the clock isn't plugged in? I beleive the clock backup power is the same as the A/C backup power. (small power given to them when the car is off) So your A/C prob is just one dodgy wire (backup power), which is why it resets. Your clock might have no power at all by the sounds of it.

Hrmm. Yeah hoping it's a simple and obvious broken connection like you said cos this morning the auto elec made it pretty clear the only kinda problem solving he can do on the car is pretty low-level since they don't work on skylines very often. *fingers crossed* I half expect it to be a common connection broken as it would make sense to me if the clock and A/C both use the same line to remember their settings. But then, the clock is dead altogether, not just forgetful, so who knows

They said it was a potential short circuit in the dash. Makes sense, fuses don't go for no reason :P So the A/C memory and the clock are both fixed now. Oh, and in the brief fiddle I had while driving back to work, I no longer have the "clack clack clack" noise when changing the A/C settings. I wonder if maybe the motor that made that noise was looking for a particular voltage/resistance, and if it couldn't find it cos of the short, it just kept trying and stopped after a preset time (the 5-7 seconds everyone seems to hear the noise). Just a thought..

Yeah :mellow:

Though, I found out yesterday that I've now lost any kinda signal from my head unit regardless of volume / signal source or amp settings... maybe the "short" they found was the signal wire - nice one guys! Goin back monday...

hmm i once lost the memory bit of my climate control. if u look a little to the left of your steering wheel theres a little grilly bit (r33 anyhow) behind there is a plug i think its so the A/C knows the temp??? anyhow, if its unplugged, memory no longer functions i found. hope this may help

Wow, very interesting thread.

My R32 has similar dramas. Aircon compressor will not start and after trying two different clocks neither worked.

Might be time to pull the dash apart? I'm not 100% on what to look for but very interested to read that they are possibly related.

when my clock wire burnt out, the climate control would go always to 25deg everytime i turned the car on, as soon as i fixed the clock it was all good. the clock is also connected to that beepin sound when you open the doors with the lights on or the keys in.

dave....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • also possibly backed up to my filler and shat down it! 🤣
    • Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...