Jump to content
SAU Community

Pfc Boost Control Kit Wiring

jmac

By jmac,
in Engines & Forced Induction

 Share

Recommended Posts

jmac Rising Star

jmac

Posted
Posted

Hey all,

Yes, I've searched and found this:

http://www.skylinesaustralia.com/forums/in...18&hl=BCK*&st=0

and this

http://www.skylinesaustralia.com/forums/in...=8&t=92133&st=0

But I'm not sure if I've done it right. I'm ok with the plumbing side, but it's the wiring I'm not sure of.

Included below is a dodgy diagram of how it's wired up now. Also some excerpts from the BCK manual that came with the kit (in Japanese) and an old manual for the AVCR from the US Apexi site.

Car: R34 GT-T (RB25DET NEO)

BCK model no.: 415-A013

Both the PFC and BCK are only a month or two old.

Again I had the problem of having nowhere for the two-pin spade-type connector coming from the solenoid to go. :D

Has this been done this right? Or totally wrong? The car is running ok but doesn't seem to be holding consistent boost (set to 1.0kg/cm2, duty cycle 64). Please help. Thanks. :D

post-17890-1137677474.jpg

post-17890-1137677501.jpg

post-17890-1137677527.jpg

Link to comment
https://www.sau.com.au/forums/topic/102563-pfc-boost-control-kit-wiring/
Share on other sites
paulr33 Grand Master

paulr33

Posted
Posted

This guide should tell you all you need to know about the boost kit and how it connects up. Please have a read and let us know what actual problem you are having with it, as its most likely already covered in the FAQ

http://members.dodo.com.au/paul/docs/power...powerfc-faq.htm

paulr33 Grand Master

paulr33

Posted
Posted

your wiring harness that goes into the powerfc should have 5 wires and not 3. If you have the 3 pin plug and 3 wire plug that runs into the powerfc on the side (next to hand controller port) then you have the wrong boost kit. The ER34 uses the 5 pin boost kit

jmac Rising Star

jmac

Posted
  • Author
Posted

:O

I have part no 415-A013... which suits the ER34... which has 3 wires coming from the MAP sensor and 2 spare pins on the plug which goes into the PFC.

I printed out that FAQ and took it to the workshop with me at the time of the install and it isn't entirely revealing...

The pressure sensor has the main wiring harness directly attached to itself, one end plugs into the 5 pin port on the PowerFC. The solenoid piggybacks off the Pressure Sensor wiring harness which leads to the PowerFC connector port. The wiring is shown below.

MAP Sensor

Red = Positive

Black = Negative (earth)

Green = Signal

Solenoid

Pink = Positive

Black = Negative

When the solenoid wiring meets with the Map Sensor harness the colours for the Soneoid change as follows;

Pink = Red

Black = Brown

I guess what I don't get is HOW the solenoid wiring is supposed to meet the MAP sensor harness, when the plug that comes on the end of the solenoid wiring doesn't directly plug into anything in an ER34 engine bay.

Now I'm confused... :O

post-17890-1137768949.jpg

jmac Rising Star

jmac

Posted
  • Author
Posted

Anyway we did a workaround tonight (see attached).

Not what it says in the FAQ (kinda) but now seems to be working... shame about the whole raining thing and therefore no traction in 1st, 2nd, 3rd or 4th.... :O

post-17890-1137769460.jpg

Sydneykid Grand Master

Sydneykid

Posted
Posted
Anyway we did a workaround tonight (see attached). 

Not what it says in the FAQ (kinda) but now seems to be working... shame about the whole raining thing and therefore no traction in 1st, 2nd, 3rd or 4th....  :(

That is correct, the BKC solenoid connects to the standard wiring harness in place of the standard boost control solenoid.

:( cheers :D

paulr33 Grand Master

paulr33

Posted
Posted

The r33 boost kit connects the pfc boost solenoid to the standard boost control solenoid wires in the engine bay.

I was unaware the r34 had the same or a similar boost solneoid by factory.

Usually if the boost kit has 5 pin with 5 wires then the boost solenoid and map sensor run to the ecu via that single plug into the boost controller kit port and the powerfc turns the solenoid on/off via the 5 pin plug.

I find it odd that you have the 5 pin plug and wires and the solenoid runs to the standard factory wires in the engine bay. so there are 2 wires on the loom unused then ?

The guide was updated about a week ago to reflect the new stuff i had found on the boost control kit after i tried with NateR31 to get his working on his r33 and the printout you've got was the original stuff I had which was a bit brief and didnt explain a great deal

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Well, this is probably where a wiring diagram and a multimeter come into play.
    • Jarsky
      gauge needle removal

      By Jarsky · Posted

      I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Jarsky
      R33 GTST Axles

      By Jarsky · Posted

      Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
    • Jarsky
      R34 Speedo not working after manual swap

      By Jarsky · Posted

      Ive converted a few clusters for the R33 with 320km/h dials. On the back there are some pads which can be bridged or unbridged (using solder or wick braid) to calibrate it. There is one bridge which is for MPH <> KPH; and there are combinations of bridges to offset it. There is probably a diagram  For example; this is my conversion for a 180km/h dial to a 320km/h dial (I put custom GT-R dials on it with the GTS25t layout) If you have J2 soldered (assuming the S clusters have a similar config to the R clusters); you may need to remove that solder
    • Rezz
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By Rezz · Posted

      Back on topic 😉, these are some of the notable pages from the booklets that are supplied with each weekly parts update. I never knew the BNR32 test mule car had an S13 Silvia front end... *Edit: On closer inspection the test car still had the R32 body, but only the front end had Silvia panels etc.
×
×
  • Create New...