Jump to content
SAU Community

Recommended Posts

OK as far as CAMS goes here's the info:

1st job is to get the affiliation. This entitles us to get L2S licences and compete at club events.

For an event to be coverd by the CAMS Public Liability Insurance we need a permit from CAMS.

To run an event and get a permit issued we need acredited scrutineers, Clerk of the Course, trained Marshalls etc.

This is not going to happen overnight. In the short term we should use organisations like Aaron McGill to run these things for us.

Dino, you 100% sure about the requirements? I thought we were covered as long as we notify cams first. The clerk of course etc is only for speed events, I think.

Oh, and I'll be along :P

If CAMS doesn't give us insurance, just go with McGill, Finlay etc. They already have to have the insurance, so the only cost for them is the day itself.

OK CAMS got back to me.

No probs. as long as we call it a training day or similar and don't have timed evnents and prizes etc.

In the short term this is the go. Eventually we will do Motorkhanas etc.

Lets look at doing it in a couple of months as a Club event.

If you guys wish to organise another event before then and get the insurance etc. don't let the Club event preclude you from doing that.

:D

this is how it is panning out

private daythrough a mcgill

i recon 20 cars max, this means the cost will be around 160(lots of room and everyone gets a really good go

30 car max cost 120 each, getting as cramped as you really would want before getting the shits (we had 40 on sunday and it was too full)

i would rather 150 and get a shitload of time because it would be a shitload of fun and the fact we would be pushing it to get that many car( i personally can fill 7 of these spots)

definate price will be back to me by late this afternoon

pete

Originally posted by red900ss

You participate at your own risk.

The insurance is public liability insurance. Like if Joe Public walks through the course and gets run over.

Yerp i know :) so to be entitled to public liability insurance you have to be a club member ?



  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...