Jump to content
SAU Community

Recommended Posts

Hey every1.

I was driving around a bit yesterday and had the aircon going pretty hard most of the day. Last nite was on chapel st when some hose under the engine broke and water started gushing out. My car started overheating and revving higher on idle so i stopped luckily in time before the temp reached into the red (it reached about 3/4 of the way up). I opend the radiator and empty, a bit of steam came out and thats it. Underneathe the car there was a loud hissing noise from the water hitting the exhaust i think. It seams to be coming out of the area around the back of the block/dump pipe area.

My mate reckons its prob the heater hose that has broken since i was using air-con all day. (pretty easy to fix i heard)

What i am concerned about is if its the coolant hose to the turbo that may have broken. ( i have just had the turbo refitted since the gasket needed replacing) If so its prob the mechanics fault for not fitting it properly.

Now this i dont mind (replacing the coolant hose shouldnt be an expensive problem). What i do care about is if my engine/turbo have sustained any damage as a result of this event.

Any experiences/advice much appreciated

Taso

Link to comment
https://www.sau.com.au/forums/topic/102826-burst-water-hose/
Share on other sites

I had my friends dad look at it 2nite, he couldnt locate the problem but said that it was coming from somewhere behind the gearbox. Is this where the heater hose is located.

Its leaking really bad, the entire radiator is basically drained after a couple of minutes, i'm gonna havee to have it towed to the mechanics i think coz i dont want to cook the engine. (Malvern to Oakleigh)

Is this a common symptom of a failed heater hose?

Rad/heater hoses have a habbit of letting go during the hotter weather.

When it dries look for white stains caused by the coolant.

Yea thought that might be the case, I guess in Japan they don't have 40+degrees, bloody Melbourne weather!!

Chances are its one of the little hoses located around near the back of the head - under the plenum. A real pain in the arse to get to. :S

Its not so much the 40degree heat but more so the age of the car.

When one starts going they soon all follow.

My little U shaped hose that runs around the back of the head went, then as it was only a small leak I left it and waited until the new motor went in, THEN the little hose that joins the pipe work that connects to the in manifold went, when pulling it off I noticed there was another little hose that connected to the block that fed in to the heater hose, that too was stuffed. ;)

My little U shaped hose that runs around the back of the head went, then as it was only a small leak I left it and waited until the new motor went in, THEN the little hose that joins the pipe work that connects to the in manifold went, when pulling it off I noticed there was another little hose that connected to the block that fed in to the heater hose, that too was stuffed. :P

Worst case scenario, if that happened to my car, how much $$$ do u reckon i'm up for. (If anything connected with the manifold/turbo is broke i'm gonna skitz it at the mechanic cause they just refitted it)

You can't skitz at the mechanic if a ~10yr rubber hose has decided to sh*t its self. :)

BUT.. that being said he shouldn't charge you for labour as he should have had a look and feel of the hoses being refitted.

Most mechanics don't give a sh*t and simply refit everything back up.

The ones that do and call you up saying this is stuffed thats stuffed generally end up being viewed as a mechanic thats trying to make more $$.

No win situation. :cheers:

Edited by Cubes

turbo feed hose went on mine.. pain in the ass to change too cos there is no room.

best way to look is to fill it back up, and see where is leaks from.. with the engine off so you its easy to get in there and see.

oil feed to turbo would help protect it and keep it coolish

turbo feed hose went on mine.. pain in the ass to change too cos there is no room.

best way to look is to fill it back up, and see where is leaks from.. with the engine off so you its easy to get in there and see.

oil feed to turbo would help protect it and keep it coolish

That is what it ended up being, took mechanics bout 30min to fix.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...