Jump to content
SAU Community

Recommended Posts

ok guys time for a change..

car is as follows..

1995 gtst, last of the series 1..

63,000km

full suspension setup including tein ha's,

and complete whiteline kit

600x300x100 fmic with chrome piping

heavy duty clutch

full professional respray to yellow including new window seals and sprayed under bonnet, got gtr rear wing, gtr front bar and side skirts

el blue/green dash lights

dual stage boost controller

3inch dump and tanabe cat back exhaust

K and N air filter

turbosmart type 3 BOV

full bride racing seat replacing drivers seat

ive also got a power fc sitting in my room which is ready to be installed and a hks super dragger exhaust with a 3inch cat sitting in my garage.. if u wanted to swap exhausts

umm think thats about it on the car.. with power fc installed and tuned i think 190rwkw on approx 12 psi should be possible with her..

$27,500

im sure if anyone was buying a car they could figure out how much ive spent on the car.. no stupid offers please

Link to comment
https://www.sau.com.au/forums/topic/10362-yellow-33-gtst-for-sale/
Share on other sites

i only just decided to sell this week.. im not in a huge huge rush to sell her.. ive put alot of time and $$$$ into the car....

i thought about putting some rims on her but decided not to.. i like the more jap style drift rims which most ppl dont like.. adn 16inch rubber is cheap too.. rims arnt that expensive.. whoever buys it can put what they like on it..

and to all those ppl asking for me to seperate parts off her..im going to try to sell it off as one for a while and if that doesnt work.. im gonna strip her back to near stock and sell of all the bits.. chances are i would most prob make more money that way but im a lazy ass and would rather sell it without the hassle...

thats fair enough :D

i too like the drift style rims :) well i'm basically waiting on my insurance money to come through since some fool ran into me.. so once i get that i'm in the market for an r33, and yours seems like it has hte goods and the looks what i'm after. I'll watch the thread and if it sells it sells if not , u have one keen buyer here when the time comes. :)

later

mark

mark ill try to get some photos for u this week sometime..

damm i need to invest in a digital camera..

Originally posted by qikshift

can't wait to see em ;) mmm bride seat :) if you still ahve the car i'll prob make the trip to nsw when my insurance shit comes through :) very impressed ...

thats if u still have it or course :)

mark

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
    • EMU Classic. For what I need it to do I see no reason to upgrade. Link and Haltech would both cost an extra chunk of money for a lot of unutilized features
×
×
  • Create New...