Jump to content
SAU Community

Recommended Posts

Hey Guys,

Im returning my S1 R33 car to stock and need the following parts:

Items to source still;

1. I have a R33 Custom Veilside Front Bar (silver) wanting to swap with a GTR or 400R Bar (pic attached) The mouth opening on the veilside is the largest as it is custom made.

2. Standard R33 Turbo (prefer S2) 45V5 with the u turn piece on the turbo (low KM)

3. R33 Air Bar Steering Wheel - Good Condition

4. Dash Console Tray (tray under the stereo).

5. Turbo to AFM Plastic thing

Items collected;

1. Climate Control Unit

2. R33 Stock Cooler with all the piping & hoses and clamps.

Thanks in advance.

Im in melbourne so i can pickup. Please PM me if you have any of the following parts. Will take stuff from interstate.

Cheers

AK

post-4729-1139088551.jpg

Edited by WLD747
bl4ck32 you have pm,but does anyone know if the r32 piping and setup is the same as the 33?

Nope, R32GTST is different, the intercooler outlet comes off the front, instead of the rear.

:( cheers :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thank you, 100% the intent. New coils were due and the 17" sixers look/feel loads better than the stock wheels. The aero options are so spot on.   Thanks for the warm welcome, all!
    • 98 r34 gtt Been rocking my latest setup and car running like never before. Have put a good 200 miles on it since all the latest changes and additions. everything is dialed in and have been driving it a bunch.   However, all a sudden last weekend as soon as I pushed throttle passed 4k and the engine stumbles, (slow or fast acceleration) hesitates and doesn’t go above 4100 or so, like a misfire. Everything else seems fine. I had a “good” set of coil packs that I removed from car when I first got it when I changed them over to new coils. I swapped out current ones for those, but no change. I also changed the plugs, no change. Seems to rev over 4 when out of gear with no load just fine no “misfire”, but as soon as its in gear with a load of any kind, it “misfires” as soon as rpm drop back below 4 k it runs perfectly, smooth, starts, restarts and drives fine as long as I keep it below 4 k while in gear. All readings look fine, no CEL   Any idea as to what could all a sudden cause an issue when pushing rpms passed 4 k?
    • When you say your cams are 272/262 is that 272in and 262ex?
    • We're arguing semantics. I am saying 45 accel and a 55 deccel ramp are "2 ways". Even a 45 degree ramp and an 89 degree ramp is "2 ways", because it is literally... two ways. The cusco 55/30 ramp is a 2 way. It's two ways. I get it though - in normal nomenclature a "2 way" would be 45/45 or 55/55 or 60/60 i.e the same locking in both directions. And something like 45/65 would be considered "1.5 way". I would then say if we're getting into the nitty gritty then every locking diff is a "2 way" diff and we should not speak in 1.5, or 2 ways but ramp angles instead. Which ofc if one of those ramp angles is 90deg, that side is not doing any locking. :p So Nismo don't obviously sell 3 things. The fact of the matter that they only sell two items really goes to show that there's a 2 way and a "1,5 way" which is really a 1 way. I believe the actual lockup for the 'adjustability' of the GT pro is really just setting preload for when the ramps actually start locking up. It's not changing how much 'wayness' there is. It is (somehow) horribly explained. People just buy whatever diff and go "locks up good bruh" and that's what ends up on socials forever.  
×
×
  • Create New...