Jump to content
SAU Community

Recommended Posts

Ok, now everyone says that N/A needs backpressure and stuff and i've been doing some testing with my exhaust and my car.

Basically i have a STOCK R34 25 GT (non turbo)

with the exhaust from factory i have a very nice torque for 2k-4k which then drops

but after i modified the exhaust to bigger and more free flowing

i LOST that down low torque, however gained alot more from 4k-redline.

Im just thinking if i could basically run 1 stock exhaust and then have a flap to a 2nd exhaust with the same diametre, and have a flap open as i hit 4k. so down low, i have the low torque. but if im doing some foot to floor driving, i get the higher range or torque.

sound good? (also should help put this debate of backpressure to rest)

(more power without back pressure, however thats only at redline/high revs.. to an extent of course)

Link to comment
https://www.sau.com.au/forums/topic/104740-exhaust-mod-idea/
Share on other sites

just to clarify someone explained to me quite a while ago here in SAU that its not backpressure, but infact volumetric vacuum.

my R33 has something similar with the stock exhaust - basically has a flap with a pulley set up and opens up around 3500-4000rpm

you can hear the thing rattle a bit too..

http://www.hks-hokkaido.co.jp/movie/muffle...hipower_sky.avi

i think this is what ant95GTR is talking about (correct me if i'm wrong)

i reckon this has more to do with silencing than low rpm torque - sounds tough as though!!!!

eug

There are a couple of OEMs (Aston Martin is doing it on a couple of their cars in their range these days, off the top of my head) that do something like this.

At a certain RPM a valve opens in the exhaust, providing more flow up top. I don't know if it just bypasses the centre muffler or if it opens a completely separate set of pipes, but either way the Vanquish and V8 Vantage get a whole bunch of noise high in the rev range.

I'm considering doing something similar in my car if I ever replace the exhaust again. I was going to set up a bypass valve to route gasses around the centre mufflers at high RPM. I'd have it automatically controlled (say at a certain RPM above a certain speed. So on a stationary noise test or in first, and perhaps second, gear it wouldn't open at all) but with a manual override for when I hit the track.

sound similar yes, if its turbo u hear the turbo spool which alters the sound of the engine quite abit, but if u have an ear for it you can still tell its a skyline :P

but no WRX have the distinctive noise because its a boxer engine.

Yea.. my stock exhaust had that flap thing.. I remember when i bought it I was checking out the exhaust going.. ok someone riced my exhaust and only one is open...

Meh it sounded like crap and looked like crap tho...

As seen below..It's actually a pretty cool shot, except my new exhaust looks alot nicer.. no pics of it atm though because, my car is in repair.. Wet roads and my stupidity... :(

oidmqv.jpg

but no WRX have the distinctive noise because its a boxer engine.

Not exactly, as lingering soul pointed out.

The "boxer throb" you get from Subies is because of the crap design of the exhaust, which is forced upon them by the crap design of the engine. I could just as easily make any sound like that. The difference is that its a packaging requirement on a turbo boxer 4, and stupidity on any other kind of engine.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If it dies, then bypass. The task isn't difficult. I have one running on a standard R32 FPCM. That's after nearly 20 years of it running an 040, which pull substantially more current than the Walbro. They're not the same module, but I'd hope it indicates that the R33 one should be man enough for the job. I think people kill them when putting proper sized pumps on them, not these little toy pumps we're talking about here.
    • Silicone spray won't hurt anything. And if it does, that's an opportunity to put some solid steel spherical bushings in, so you can really learn what suspension noise sounds like, If you're going to try it, just spray one bush at a time, so you can work out which one is actually noisy. My best guess is that if the noise started only since putting the coilovers in, then it is just noise being transmitted up through the top mounts of the struts, and not necessarily "new" noise from bushes. But it's almost impossible to know.
    • Are you saying the 34 is SUV height, and not that we're talking about an SUV here? (because if we're talking about an SUV, you don't fix them. You just replace them when something breaks. Not worth establishing sufficient emotional connection with an SUV to warrant doing any work on one). I wouldn't jack my car up on a short little loop of 10mm steel rod poking out through a hole in the bumper bar, front or rear end. I realise that we're probably not talking about that type of loop at the front, being the one under/behind the bar on a Skyline.... but even for that one, trying to jack up on what amounts to a thin piece of steel, designed purely for withstanding a horizontal tension force, not a vertical compressive force (and so would be prone to buckling/crushing) and, my most particular bitch about it - located RIGHT AT THE EXTREME FRONT OF THE CAR, applying a load up through the radiator support panel, etc, with almost the entire mass of the car cantilevered between there and the rear wheels? Nope. Not doing that. Not on the regular. That structure out there in front of the front crossmember is not designed to carry load in the vertical direction. Not really designed to carry any load at all, really. The chassis rail that the tow point is connected to would be fine loaded in tension, as per towing. Not intended to carry the mass of the whole car, especially loaded all on one rail, with twisting and all sorts of shitty load distribution going on. No, I will happily drive up on some pieces of wood, thanks. That can only happen on driven wheels, and they are at the other end of the car, and this problem does not exist at that end of the car. And even then, I have been known to drive up on at least 1x piece of 2x8 each side at the rear, simply to reduce the amount of jack pumping necessary to get the car up high enough for the jack stands. What really really shits me about Skylines is the lack of decent places for chassis stands at either end of the car. You'd think they'd be designed into the crossmembers.
    • I've got MCA Blues on my V36 Skyline, and while I've managed to sort out issues with scrubbing/bottoming out by raising it a smidge and increasing the damping hardness, the rear end still sounds *super* noisy when driving on anything other than the flattest surface imaginable. It sounds like a small party of flamingos are just chatting away in the back, which makes me think there are several link points in the suspension contributing to the noise. Am I hearing dried out/worn bushings? None of it sounds like metal-on-metal, it sounds more like hard rubber squeaking on metal. It's been suggested that a bit of silicon spray on each bushing might quiet them down, but I'm not sure what material the current bushings are made of (probably factory, I imagine) and whether silicon spray will degrade that material.
    • The obvious answer here is get a ND2/3 RF with the Targa top. The red is nicer, too!
×
×
  • Create New...