Jump to content
SAU Community

Recommended Posts

it seems like dynodynamics on shootoutmode is the popular choice for a dyno readout but ive heard recently that autosalon changed their dyno to a mainline dyno . which one is more accurate?

two different dyno's (mainline and dyno dynamics) in the same city (around 5 klms apart), two days apart with similar barometric conditions. read within less than 1% of each other. With the same vehicle.

Not bad eh!....pretty acurate

ive heard recently that autosalon changed their dyno to a mainline dyno . which one is more accurate?

and yeah, just on that... the Cabin group have been using mainline dynos since 2002/3.

So its far from "recent" news

two different dyno's (mainline and dyno dynamics) in the same city (around 5 klms apart), two days apart with similar barometric conditions. read within less than 1% of each other. With the same vehicle.

Not bad eh!....pretty acurate

Where?..which dynos? Anytime I have seen the same car go on a dynolog and then a dynamics, the dynamics always reads about 10-15% higher.

Where?..which dynos? Anytime I have seen the same car go on a dynolog and then a dynamics, the dynamics always reads about 10-15% higher.

Croydons...then Autosalon....and it was Stacey's car...so i should know.

Edited by DiRTgarage
Croydons...then Autosalon....and it was Stacey's car...so i should know.

I didn't say you didn't...but I think Cabin must have a 'special' version of the Dynolog software.

I know of a wrx that made 20% more power on CRD's dyno in the afternoon than it made on a Dynolog in the morning. There were no changes in between. Had the same tank of juice and all.

All the other dynologs I've seen read very similarly (comparing the same cars on different days)

did you record the temps on that day?

you said morning and arvo... so my bet there could have been a reasonable temp difference.

end of the day, does it really matter? anyone can can get any figure if you need too

did you record the temps on that day?

you said morning and arvo... so my bet there could have been a reasonable temp difference.

end of the day, does it really matter? anyone can can get any figure if you need too

Yep...it was slightly warmer in Syd than the gong...only a degree or 2.

Yep..I agree

I didn't say you didn't...but I think Cabin must have a 'special' version of the Dynolog software.

I know of a wrx that made 20% more power on CRD's dyno in the afternoon than it made on a Dynolog in the morning. There were no changes in between. Had the same tank of juice and all.

All the other dynologs I've seen read very similarly (comparing the same cars on different days)

Well how does this grab ya...Carlos from Millenium Motorsports ran 599kw at Queensland 2 days before Autosalon on his Mainline dyno...and at the same boost levels ran 601kw on Autosalon's dyno.....he must have the "special" software too!

Mainline dyno's even run the same no matter if its 2WD or 4WD...we proved it in front of hundreds of people at Final Battle...there was 1kw difference between the runs.

I think what Mik is trying to say is Croydon's dyno is happy...if its so happy i should be rolling almost 520AWKW......i think im gonna have a word to Jim about my deflated power figures.

Edited by DiRTgarage
I Have seen IDENTICAL results on two different dynologs equate to 40awkw more on two different dynodynamics dynos in an unchanged trim/tune. Just my experience.

highly experienced acredited operators should not have such a discrepancy...as essentially the dyno's use similar hardware.

Edited by DiRTgarage

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Need to see other side of PCB in that area...ie; I don't see any thru-hole mounting, just soldered vias (smd zeners in SOT23 have 3 legs but only 2 are used, as reflected by PCB tracks)
    • 4 to 5 is fine. It will be slow, but that's better than blowing turbos. I don't have a PS pump idle up solenoid on my car, because... I think when we put the Neo in we retained my R32 lines. But.... From inspecton of the R34 vacuum hose diagram, you can see that the solenoid needs to be connected to the turbo inlet as source of clean air) and the plenum (as source of vacuum - which is the place for the air to flow to to cause the idle to increase). So 3 to 1 is VERY WRONG. 3 should go to either the turbo inlet, or the plenum. Follow the other hose from the PS solenoid and if it goes to the plenum, then your 3 goes to 2 2 would also serve as a bleed port for a boost solenoid.
    • Pull them out and pull more apart. You can't do shit with them still bolted to the floor of the car.
    • Yes it is. ZD1 is on the other side of the board. Where ZD1 is marked is clearly opposite a 2 pin device. Our 3 pin device here is not a ZD.
    • Alright, a little update on this... I called Fulcrum, who used to be the distributor in Australia. No Bueno, they don't service them anymore.  Called shock works, who don't service them but offered to dyno the shocks for performance, and suggested DNA in Sydney might service them.  Called DNA, who also do not service them and basically said they try to steer customers away from tein for this exact reason these days- there is just no support for them anymore apparently.  Both SW and DNA said they are a not necessarily a bad product, but they just don't service the brand or know anyone who does service the brand anymore.  So... I could keep calling around but at this point I think I'll probably just spring for the shockworks product, unless anyone here knows anything.  Cheers 🍻 
×
×
  • Create New...