Jump to content
SAU Community

Recommended Posts

hi all i think i have a big problem on my hands, i own a nissan silvia with a rb20 motor now i got the car with the motor and it had rego. now the rego is close to been up and i went over all the car to make shore its all ok. i didn ot think much of it when i got the car as it all lind up the number and all but now when i had a chance to think abit a found that the rego sticker says that the engine number is ca18%$#@ now i am not shore but i think the number should start with rb20 or so if its regoed with this number

now i did find a number next to the gear box and it also says ca18%$#@ is that where the rb20 engine number is and if so should it start with rb20 or ca18

i think the number has been changed and if so what can i do make it right

plz help

pm if you have any idea thanx

Link to comment
https://www.sau.com.au/forums/topic/105398-where-is-the-rb20-engine-number/
Share on other sites

RB20 motor should have the engine number stamped on the engine just in front of the gearbox on the passenger side, and yes it should start with 'RB20'. If you have a number starting with 'CA18' on the engine then it sounds like someone has ground off the RB20 engine number and replaced it with the number of the original engine (ie the CA18 engine number). Sounds like a dodgy way to get around engineering/rego requirementts.....and most definately illegal.

Post up some photos of your engine and the engine number on it, if you can.

Edited by SteveL

This is most definately a dodgy attempt to get around engineering/rego requirements, and as I said, totally illegal. What you do about it is entirely up to you, but the question is: do you have engineering certification for the conversion ?? (I suspect not). Also, do you have details of who did the conversion, etc.

Strictly speaking you should report this to your rego authorities, who will undoubtedly want to investigate the matter.....the engine could be stolen, for example. As I said, its up to you, but remember that your rego and insurance is invalid under these circumstances.

Edit: there are ways to determine the original engine number. Without getting too technical, the process of stamping the engine number into the block leaves 'damage' to the block material beyond what you can see with the naked eye. Using a 'black' light can sometimes reveal the original engine number info.

Edited by SteveL

check under the thermostat housing.. im sure there is also a engine number there i'll check tomorow arvo on my old rb20 and let you know

at least i think thats were it is.. i'll take a camera and get photos of were it is..

Edited by Wazz

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...