Jump to content
SAU Community

Recommended Posts

Hey .... in the last few weeks i have been steadly ironing out the bugs in my recently purchased r32.

Now most of the fix's have come from experienced people on this forum who have seen most issues well before i could ever diagnose as a new owner.... thanks BIG time for that SAU's

The small issues i cant seem to solve localy or get diagnosed are as

1. turbo timer is intermitant and i am scared to turn the car of sometimes if i have moderatloey warmed up the exhaust side as sometimes it just cuts the engine ... the timer is import and only has minute change function..... Anyone know why this would happen ?

2. Car is always warmed up standing till temp is at perfect operating temp... the odd thing to me here i havent ever had ceramic twins before so i dont quite know how they react...

Anyway until boost has been run through the turbos for a minute or so they sound like a cricket in the bush ... it dosent matter how long you warm it up for . the noise will be there until you have put a few gears changes using boost ... what is this ? is it normal because as soon as its been spooled a few times the noise changes to the usual air rushing sound.....

3. this is a basic problem i havent been able to test properly my self yet ...

the car's leaving me stranded with run down battery .... Some days it fine and charging and then other days the volt meter starts to jump aound ? usualy leaving a flat battery from the engine using the battery power... this i will be sussing as today as much as i can as she let me down in public last night (out with the jumppak how humiliating) How does an alternator be good some days and not others?

is this a symtom of a voltage rectifier on a LINE because i have only seen them over charge?

Edited by ishh

1. Don't know why but don't be scared. If you are driving fairly sedately for the last 2-3 minutes of your journey then you don't need the turbo timer anyway. I rarely use mine these days.

2. Sounds like the oil isn't going through at idle.

3. I think you have a loose connection to the battery, the alternator or a major earth like the engine or chasis (there is a lead from the negative of the battery to the chasis to the engine - check that)

1. As Abo_Bob said, if you are sensible and drive sedately for the last k or so, then you don't require a TT. (The Shell Sierras would only do a "slow" lap of Sandown after practice, then simply pull into the pit garage and switch off the engine, and they had been pushing 3 bar boost through the engine)

2. The engine will warm up quicker if you drive the car. If you are sensible, and don't pull boost during that period, then no damage is likely to occur. Japs generally don't take care of their engines, so it's likely some old engine oil is baked in the turbo bearings.

1. I have turbo timer Greddy, I was panic like u, as my timer intermittently didnt work, as sometime after a drive, I turn the igntion off, the timer didnt stay on. But now i know why, not sure if its similar to urs. But here goes,

- I noticed that when i park, with gear in Neutral, but handbrake Not on, Timer will shut Off.

- If I stop, and Clutch still in, Timer shut OFF. (weird)

- If I parked, HandBrake oN, but in Gear, timer is OFf as well...

so to corect it, i come to a complete stop, handbrake Up and in neutral and clutch is oUt, then it works Normal....

hope ur problem is as simple as mine. just take me a while to realise.

cheers,

Cool thanks gang ....

1. yeah guys i always warm her down 3 or 4 kays before shutdown just piss's me off but i will give ZXFIRE soulutions a go :D

2. will keep monitoring ... its just such and odd sound if it catches me by surprise ... but as i said as soon as its all used for a bit (pressure put through turbos) chirping noise gradualy changes to air sound...

3. sorted ..... by removing alternator, inspect and refitting with secure new connections ...

Thanks again SaU's

Edited by ishh

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...