Jump to content
SAU Community

Recommended Posts

The Stagea has a vibration at speeds above around 80kmh. At first I thought it was a puncture repaired front left tyre but got that fixed and even swapped the front wheel to the back but it is still there.

Wheels have been balanced by at least 3 different places now, so not sure what is causing this. It feels like out of balance wheels but have been told it isn't, doesn't feel like an out of round wheel (my Skyline had that problem). It is a very fast but weak vibration and doesn't seem to do it at lower speeds, that I can notice.

Following a search of the threads, found this list from our guru (Sydneykid):

1. Out of balance tyres (are they balanced inner and outer? Or just one set of weights?)

2. Out of round tyres (easy to check on the balancer)

3. Out of centre wheels (do they lock securely over the hub centre?)

4. Out of round wheels (how is the run out on the inner and outer rims?)

5. Out of balance brake rotors (unusual, but does happen)

6. Worn wheel bearings (jack it up and check the movement, in and out top and bottom)

7. Worn radius rod bushes (you can see it, the rubber is torn and fluid leaking)

After that it gets obscure, eg; worn shocks can cause vibration after hitting a bump.

Therefore, should I just check each of these items in turn until find something?

Further, during my 100,000km service, the workshop noted something along the lines of front diff oil seal leaking - is this a major repair issue or just a case of replacing seals?

Link to comment
https://www.sau.com.au/forums/topic/105479-driveline-vibration-at-80kmh/
Share on other sites

mate its probably uni joints .... one has a tolerance out and is causing an unbalance vibration ... either that or you have thrown a tailshaft weight off (rare)

test by taking car to 80kms then coast (no drive) to see if it still vibrates usualy it will if its the tail shaft uni's as the tail shaft is rotating as fast as the wheels are driving it ...

Good luck!

Further, during my 100,000km service, the workshop noted something along the lines of front diff oil seal leaking - is this a major repair issue or just a case of replacing seals?

hey mate do u mean the diff front plate seal, or the sump to engine seal is leaking? the diff front plate is piss easy and the other is a pain in the arse. :P

just take front plate off, add gasket goo from nissan and put back on :(

Edited by CruiseLiner

check the tailshaft centre bearing would be my suggestion,if you've already eliminated the wheel bearings,wheels and tyres.

it's possible someone has had the shaft out before and put it back in in a different orientation. normally this won't cause a problem,but if you have a worse-than-usually-balanced shaft,it would cause what you're describing.

just out of interest,how much balancing weight is on your wheels?

if there's a lot (as in over 50grams per side),that's indicative of another problem.

Justin...

Thanks for the replies guys and it is now time to begin the hunt to determine the cause of the problem and then the fix.

Will see how it goes but at least it is still driveable

As for your question Brad, not sure as they just put it on the invoice that the "front diff seal leaking".

Sorry to hi-jack your thread, but I've got a similar problem.. I get steering wheel vibration above around 80km/h. I took it to get a balance but the guy said the vibration is because of the tyres. He said because of how the tyres have worn they are impossible to balance. He said you can try balancing them as much as you want but the vibration isn't going to go away so he'd just be 'taking my money'. He said the tread had 'feathered' and that you can tell by running your hand over the tyres. So he says I need to get new tyres to fix the problem. Could this be true or he is just trying to get me to buy new tyres??

Feathering on tyres is caused by the wheels not being aligned properly.

Get a wheel alignment done. If you buy new tyres without getting the wheels aligned, the same problem will happen and you would have wasted your money on tyres.

Thanks champ. Yea they did a wheel alignment. So this 'feathering' thing actually happens? Just get new tyres fitted and balanced and it should be good? Thanks again.

Just to add another suggestion:

Check that the casing of the tyre isn't letting go. This may show up as a deformation in the shape of the tyre - like a lump/bulge in the wall or flat part of the tread.

On a tyre on our caravan the deformation was hardly noticable at all except for the vague handling at speed.

The amount of tread left (ie age of the tyre) has little to do with it. Hitting a gutter or rock on the road may be enough to damage something internally.

If you're worried about getting had on a new set of tyres when the current tyres have plenty of life left, then keep the old set of tyres to use again later. If the new set fixes the problem then you know you can throw the old ones.

The Stagea has a vibration at speeds above around 80kmh.  At first I thought it was a puncture repaired front left tyre but got that fixed and even swapped the front wheel to the back but it is still there.

Wheels have been balanced by at least 3 different places now, so not sure what is causing this. It feels like out of balance wheels but have been told it isn't, doesn't feel like an out of round wheel (my Skyline had that problem).  It is a very fast but weak vibration and doesn't seem to do it at lower speeds, that I can notice.

Following a search of the threads, found this list from our guru (Sydneykid):

1. Out of balance tyres (are they balanced inner and outer? Or just one set of weights?)

2. Out of round tyres (easy to check on the balancer)

3. Out of centre wheels (do they lock securely over the hub centre?)

4. Out of round wheels (how is the run out on the inner and outer rims?)

5. Out of balance brake rotors (unusual, but does happen)

6. Worn wheel bearings (jack it up and check the movement, in and out top and bottom)

7. Worn radius rod bushes (you can see it, the rubber is torn and fluid leaking)

After that it gets obscure, eg; worn shocks can cause vibration after hitting a bump.

Therefore, should I just check each of these items in turn until find something?

Further, during my 100,000km service, the workshop noted something along the lines of front diff oil seal leaking - is this a major repair issue or just a case of replacing seals?

Hey

I had a similar problem with my GTR. Driveline started to vibrate on medium to hard acceleration and only when it was about 70km/h and over.

First thing to be done was the centre bearing, did look pretty worn but didnt fix it.

Wheel alignment and balance on 2 different sets of wheels. Checked all rear bushes and links.

Replaced front prop shaft as the uni joint was pretty flogged out (wasn't affecting vibration as it wouldnt make any difference with this shaft out ie 2WD).

Replaced small rubber and metal sleeve mounts for gearbox crossmember, again, worn out but didnt fix problem.

Took out tailshaft and put back in but rotated it around from original position. From what the mechanic told me there is 4 different ways for it to go back in. He moved it one mounting positon around and it was all fixed. :P

It took a bit of money and research to get it sorted for an annoying problem but probably was a good thing to get all these worn out bits n pieces replaced before they broke or caused potential damage.

Jono

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
×
×
  • Create New...