Jump to content
SAU Community

Recommended Posts

Hi Guys and gals,

Where do I get the lock nuts for HR Racing Wheels? I got the Barri-Nut lock nuts - but they are not the right size. Im guessing that only the specific HR Racing lock nuts will fit my rims. Can someone tell me where to get them in Vic?

Thanks :P

p.s I have attached the pic of my rims as well - if anyone knows where I can get hte right lock nuts - please let me know :D

post-26053-1140054556.jpg

Link to comment
https://www.sau.com.au/forums/topic/106063-wheel-lock-nuts-for-hr-racing-rims/
Share on other sites

There is another thing thats bugging me about the car - the turbo timer on it is a Starbo RS-1500 timer (apparently its an auto/remote start combination with the turbo timer) - the thing is its all in japanese. Its got 6 little levers that is either up or down - lever 1 says "ON" - but it doesnt do anything. Sometimes it works for about a minute, other times it doesnt at all. Can anyone shed some light on this as well. im guessing I will need to get another turbo timer - but I have to wait for a bit. If anyone has this, or knows how it works, please let me know. :D

Thanks all.

if it works on n off, try switching the key position to off without the door being opened or your foot on the brake pedal, cuz sometimes these are set to bypass the turbo timer. That is in the event u dont want the turbo time to be running, you can jus open the door or have your foot on the pedal and switch the car off....

about the right size lock nuts, just go to any bob-jane t-mart, they seem to have everything....good thing is, if it doesnot fit they give a replacement then n there....i have been gettin all the work done from the oakleigh one.(corner of prin hwy and warrigal road).

Ok, guys - i got the turbo timer running - but even when I am driving normally (lets say for about 10 minutes), and after i get back home, turn off the engine - it keeps running for about 2 minutes. Is this normal? or have I actually got a faulty turbo timer?

If this is indeed faulty - whats the best turbo timer to get. I was told the Apexi turbo timers are excellent, and cost about $120 to buy.

Thanks in advance.

thans for the reply nate - its just that I went to get pizza (about 4-5 mins from my house) - I stop the car and it was on for 2 mins - so i was just thinking -thats a bit excessive....

what tt is it? if the instructions are jap chances are the auto mode isnt hooked up right? AFAIK, its just 12v/ign/acc and thats it i think, i have a manual one which is set to 2mins all the time.

as i put on one of the posts above -> its a Starbo RS-1500

Its all in japanese - and I have no idea what the 12v/ign/acc is......:D

the only way I will find out i guess, is after i get back from a long drive.. and see how it goes - or I can post a pic of the turbo timer up tommorrow....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
×
×
  • Create New...