Jump to content
SAU Community

300zx / R31 Brakes

YO880
 Share

Recommended Posts

YO880 Mentor

YO880

Posted
Posted

Hi Guys, i had collected the following parts for a brake upgrade on my Datsun 240K. Unfortunately i am heading in a different brake direction now and have the following for sale! i would prefer to keep the front parts together, and the rear parts together, but i will sell the DBA rotors seperately.

Pair of Nissan 300ZX Non-Turbo 4 piston Alluminimum 26mm calipers

300ZX calipers sandblasted and powdercoated red

set of 300ZX caliper seals

post-124-1140572333.jpg

paid $400 total, sell for $270

Pair of Nissan R31 Pintara single pot calipers

calipers sandblasted and powdercoated in red

brand new set of R31 caliper seals

Set of used R31 pintara rotors

set of brand new Ferodo Extra Pads

2x brand new DBA Slotted 616 rotors

post-124-1140572317.jpg

paid $568 total, sell all for $450, DBA rotors for $250, rest for $200 (the cost of the powdercoating and the new pads!)

located in sydney, calipers have not been used since powdercoating

Link to comment
https://www.sau.com.au/forums/topic/106837-300zx-r31-brakes/
Share on other sites
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Leak from Tokico BM50 Brake Master Cylinder

      By GTSBoy · Posted

      The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • No Crust Racing
      R32 Gtst - Track Car

      By No Crust Racing · Posted

      Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • MBS206
      R32 Gtst - Track Car

      By MBS206 · Posted

      I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
    • PranK
      eBay "Hella" oil level sensor

      By PranK · Posted

      Yeah, I guess its pretty easy to get to if this doesn't work. Just wait till next oil change and pull it out. I am going to have to do the oil pan gasket soon and thought I'd just replace it while I was there.  Thanks
    • Dose Pipe Sutututu
      R32 Gtst - Track Car

      By Dose Pipe Sutututu · Posted

      All that matters is you're safe and you were able to type that post. Hopefully heaps of parts you can recover for the next shell.  
×
×
  • Create New...