Jump to content
SAU Community

Recommended Posts

Any one seen/purchased these rims?

http://www.modyourcar.com.au/product_info....roducts_id=4428

They look to be alright, very similar to the nismo ones (and at an affordable price) which im looking for. Looks to be a set offset, so will the +30 17x9" for the front and +15 17x9.5" for the rear fit a r34?

Link to comment
https://www.sau.com.au/forums/topic/107019-nismo-lm-gt4-rims/
Share on other sites

its probably as good as im going to get on my car budget, they dont look too different from the lm's which i will never be able to afford. The offset mentioned on the site, do you think they should fit the skyline?

thanks for the replies; i guess 17x9 (all round) should do the trick then. Will probably have to lower the car at the same time also....so it wont look too goofy.

Edited by RyanN

17x9 +30 offset for the fronts you will most likely run into problems when u lower it. ideally you would want 17x8 in the front and 17x9 in the rears with a +30ish offset. 17x9.5 +15 for the rears will stick out like dogs balls and will rub ur guards when you try lowering ur car.

U might wanna chk these out as well look much better IMO

http://www.nissansilvia.com/forums/index.p...pic=117430&st=0

17x9 +30 offset for the fronts you will most likely run into problems when u lower it. ideally you would want 17x8 in the front and 17x9 in the rears with a +30ish offset. 17x9.5 +15 for the rears will stick out like dogs balls and will rub ur guards when you try lowering ur car.

U might wanna chk these out as well look much better IMO

http://www.nissansilvia.com/forums/index.p...pic=117430&st=0

would the different tyre widths screw with the HICAS ?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If you take the top half of the intake off you can unbolt the flap off the shaft and leave the shaft in there blocking the hole. Then you can remove the little vacuum canister off from under the manifold and get a spare vacuum line to run to the ECU. I can take some photos of it later. Probably best to get the vacuum source to the ECU sorted first though. Mine all worked mint with the base map from the GTT an I've pretty much let the closed loop sort the fueling and took 1 degree out of the whole timing map.
    • This IS something you also have to configure in Haltech (or at least I did in the past when going from onboard-to-ECU map sensor and an external MAP sensor in haltech land).
    • I'm hoping it's something as simple as the ECU is looking for an external MAP sensor, but he is trying to use the onboard MAP sensor.
    • You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
×
×
  • Create New...