Jump to content
SAU Community

What is PSI??


Recommended Posts

The other guys have most of it right.

Yes it does mean pounds per square inch, this was the old imperial measurement for pressure. Bar has been since we moved over to metric. Americans still use imperial mesurements on somethings, and so psi is still commonly used.

Pressure is a measure of force over area.

Most engines will run at a vacuum while idling, an NA engine will go to 0psi at full throttle, a turbo engine will create a positive pressure over and above atmospheric pressure.

See'ya:burnout:

Link to comment
https://www.sau.com.au/forums/topic/10755-what-is-psi/#findComment-174371
Share on other sites

Actually I think atmospheric pressure is 1 bar or about 14psi?

That is the amount of all air above us pressing down on all objects on earth (air has mass and weight as any other materials). This is accepted as the standard pressure. We don't feel the air pressing against our skin or eyes coz our body is designed to adapt to it thru our evolution. Otherwise we'll all b crushed to death by now.

So actually NA engine actually runs the same pressure as the atmosphere at full throttle. Turbo engine runs more than the atmospheric level, depending on boost controller.

However to make things easier, the atmospheric pressure is set as 0 psi on boost gauges. So if your factory boost gauges shows 7 psi, that means the air pressure going into the engine is the 7 psi above atmospheric pressure... you are running positive pressure....

Sounds confusing, I read that thing from howstuffworks.com, however to avoid further confusion, let's accept that NA engine runs 0 psi (on boost gauge) on full throtle, and factory R33 boost is around +6-7 psi on the boost gauge.

Link to comment
https://www.sau.com.au/forums/topic/10755-what-is-psi/#findComment-175294
Share on other sites

psi, psia, psid, psig

traditional symbols for pressure units used in hydraulics and plumbing. psi is a symbol for pound per square inch (see above). psig is a symbol for pound per square inch gauge; this means that the pressure has been read from a gauge which actually measures the difference between the pressure of the fluid and the pressure of the atmosphere. psia means pound per square inch absolute, which is the total pressure including the pressure of the atmosphere. psid, pound per square inch differential, is a symbol for a difference between two pressures, neither of which is atmospheric pressure. Corresponding symbols for pound per square foot (psf, etc.) are also used.

Link to comment
https://www.sau.com.au/forums/topic/10755-what-is-psi/#findComment-175315
Share on other sites

OH and while I am at it

PS = pferdestärke

German word for horsepower, meaning the metric horsepower. The symbol ps is used for horsepower in both the Japanese and German automotive industies.

HP = Horse power (Metric Horse power)

a unit of power, defined to be the power required to raise a mass of 75 kilograms at a velocity of 1 meter per second. This is approximately 735.499 watts or 0.986 32 horsepower. The unit is also known by its French name cheval vapeur or its German name pferdestärke.

:)

Link to comment
https://www.sau.com.au/forums/topic/10755-what-is-psi/#findComment-175319
Share on other sites

The japanese like to use PS as their measurement for horsepower! Conversion is 1 horsepower = 1.01387 PS

Brake horsepower (bhp), sometimes called shaft horsepower, is the amount of power available for useful work. Bhp is less than flywheel hp because of the various power losses which occur during engine operation.

To determine the brake or shaft horsepower that is delivered as useful work by an engine, the sum total of all mechanical losses must be deducted from the total HP (initial or flywheel horsepower). BHP is the reading that dyno's use! This is also sometimes called RWHP or Rear Wheel Horsepower!

Here is an online conveter so if you know your HP and want to find out the PS/KW

http://locost7.info/converter.php

MEGA

Link to comment
https://www.sau.com.au/forums/topic/10755-what-is-psi/#findComment-177053
Share on other sites

rs73,

Your right that atmo is about 1 bar, that's why I said that turbo engines read over and above atmospheric, while NA reads 0psi relative to atmo.

So we are in fact using psig, relative to gauge pressure, that is we take all measurement relative to 1atm.

See'ya:burnout:

Link to comment
https://www.sau.com.au/forums/topic/10755-what-is-psi/#findComment-177065
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...