Jump to content
SAU Community

Recommended Posts

i Think its the injector resister pack i talking bout its a little silver fuse looking thing bolts to your chassis i think on the strut tower in bay not 100% sure wat this does as i dont have one and neither does my mate r32 gtst but i have trouble starting it and my mech says this is the problem could it be or should i be looking at some other cause any help would be great thanks guys

OH and how much power should i expect and ET with followin setup

S13 silvia

Rb20DET

FMIC

VG30deT turbo

SAFC11

ARSM

3'' DUMP

3'' Zorst

Fuel Pump

12 PSIEXCEDY CLUTCH

Link to comment
https://www.sau.com.au/forums/topic/108292-need-help/
Share on other sites

k thanks mate any ideas as to why it may be hard to start could it be fuel as it has sat for around 5mnths

Who wired up the RB20? What fuel pump do you have? Is it hard to start all the time or only when its cold?

If the standard injectors are used there will be no resistor pack as the RB20s have high impedance injectors (as opposed to the GTRs with low impedance and hence the resister pack).

`

Link to comment
https://www.sau.com.au/forums/topic/108292-need-help/#findComment-1996276
Share on other sites

hey guys i have told the tuner to try it with out the resister pack and what do you know it works all fine and af ratio stays steady all the way but now i have a missfire i think it is the coil packs so have to check that out this week but almost done i will try and post picks for you guys soon hopefully i get the power figure i want fingers crossed

Link to comment
https://www.sau.com.au/forums/topic/108292-need-help/#findComment-2011020
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...