Jump to content
SAU Community

Problem With R33 - Too Much Fuel/air? :s

RedEmblem

By RedEmblem,
in Engines & Forced Induction

 Share

Recommended Posts

RedEmblem Proficient

RedEmblem

Posted
Posted

Hey guys,

A friend of mine has an R33 S2 GTST. It's reasonably modded - Intercooler, clutch, Mines ECU and I believe a T28 turbo. The problem is, whenever you drive it - no matter if you drive it slowly or if you give it a bit - it feels like it's bogging down. It feels like the clutch is slipping - the revs just climb and you dont go anywhere. If you put your foot on the clutch and rev it a bit it goes away for a small while and then returns. Apparently this started happening when the orginal turbo shattered and the T28 was installed.

Any ideas?

We put the stock ECU back in last night and the problem was still there.

Thanks.

Link to comment
https://www.sau.com.au/forums/topic/108738-problem-with-r33-too-much-fuelair-s/
Share on other sites
RedEmblem Proficient

RedEmblem

Posted
  • Author
Posted

Yer, but does clutch slippage act like that?? :S

I should also point out that the car has been doing this for about 8-9 months now (I dont know how the driver has put up with it). And the problem hasnt gotten better or worse. Wouldnt a slipping clutch get worse?? - Occasionally the problem goes away for a few hours (maybe once every two weeks?) .

paulr33 Grand Master

paulr33

Posted
Posted

if its always been like that then it might not be clutch

generally the clutch slip will get worse and worse, and then just completely fail. it could be that its just stupidly rich and when you put the stock ecu on youve hit the stock rich and retard protection. turn the boost way down to like 7psi and see if you have the same problem.

if you dont, get a real ecu (read: powerfc)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • GTSBoy
      R32 GTS (RB20DE) Injectors Replacement

      By GTSBoy · Posted

      No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • codygrimm27
      Can you mount the ATTESA pump in other locations?

      By codygrimm27 · Posted

      Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...