Jump to content
SAU Community

Recommended Posts

get a Ninja Case :laugh::D

http://www.pccasegear.com.au/prod3033.htm

somthing like this PSU will do fine no need to go over the top that GFX card doesnt even run its own molex

http://www.pccasegear.com.au/prod3598.htm

i just remebered b4 ive used this ebay seller is very prompt and is in adelaide to

Ebay PSU

EDIT

Vista Home Premium

i bought a copy of XP of him and bould buy more things

EDIT

Mobo CPU and Ram combo

Edited by Madaz

so, i has a small problem.

well, a few small problems.

1. my connection speed is as low as 1mpbs. (using a belkin 54g, a few hours ago it wouldnt connect, period, stuffed if i know how i managed to connect).

2. most of my usual sites load, with the exception of the r31skylineclub... and i know that isnt down.

so, any suggestions and such?

A few things to try off the top of my head...

Power off/on the modem

-If sync/speed is still bad disconnect every phone in the house from the phone line and power off/on the modem again and check sync speed.

--If it improves you know you have a dead line filter (not common but does happen). Isolate the dead line filter by connecting a single phone at a time and calling it with your mobile while watching for sync/speed drops and transfer interuptions.

Are you on ADSL2?

-Change your line profile to a 'reliable' profile to improve stability as they ncorporate interleaving which as a result increases ping so not so good for online gaming but its better than having poor stability.

Changing the line profile to reliable profile works well on those wet days where water gets in to the lines causing a little cross talk that results in poor stability/reduced sync speeds. I've had to do this almost every winter :whistling: Then wait for telstra to get out and fix the lines. In the last recent downpoor the phone line dropped out completely, unable to receive or make calls (no dial tone with lots of crackling and static) I called internode had them throw me on the very high reliability line profile and I connected at just under 1mbps. It took 3 days for telstra to sort out the problem. :S

and ....... Call your ISP. :)

well, unplugged all the phones and such, the connections a little better, but its still slow (>12mbps) and its still fairly unstable, but its better than it was 10 minutes ago, ill call belkin and internode tomorrow and see whats up.

i doubt its internode though, looks more like the routers f**ked, had so many problems with it...

Linksys, Billion & cisco (out of reach) modems for me. I prefer billion modems.

Always have a quick look at

http://cgi.internode.on.net/advisories/list.html?area=1

to notify of any issues.

Most likely the telstra line that runs from the internodes hardware in the exchange to your modem/router.

In the meanwhile if transfers web browsing and transfers are unstable throw yourself on a more reliable line profile (done via internodes web site and monitor when the modem resync's on its new more stable line profile)

You should be fine with the high reliable profile, very high profile may be a little overkill.

Failing that do the usual virus scan & spyware/malware scan.

spyware/malware - lavasoft adware, spybot and the VERY usefull prevx1.

If your familiar with services that are supposed to be running hijackthis is also a handy tool to use. I tend to use all three on problem computers.

try looking @ a Mitac EL80 one of my mates bought one and he was very impressed there is also overclockers AU did a review and other boards that you can google

i had links for you but i dont know what happened if i closed browser before submitting doh!

...so far netgear seems solid...

I've had good experiences with netgear stuff too.

While I haven't used a WIDE range of stuff, the products I've used have always perfomed as I'd expect them to, with no issues.

That's all I really ask for in hardware, and for the price I'd recommend them.

This is usually the part where 5000 people chime in with "XYZ is so much better", and while they may be, until I find a product doesn't do something I need, it doesn't need changing.

alieware are sooo overpriced but its your money

my mate bought one of there P4 3.6 laptops over a year ago think weighs like 14kg comes with it own backpack cost him 4g had like a 7800gtx or something in it

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...