Jump to content
SAU Community

Recommended Posts

I think you're still looking around the 1100 - 1300 dollar mark.

I get the feeling though that some time in the future sony may release a fully software emulation of the ps2 hardware for ps3. And then you won't need to get a 60gig. Thats just a bit of an eduated guess.

so its true you cant play ps2 games on a 40gb ps3 :rofl: i thought that sounded fishy but hey we are talking about sony

I think you're still looking around the 1100 - 1300 dollar mark.

I get the feeling though that some time in the future sony may release a fully software emulation of the ps2 hardware for ps3. And then you won't need to get a 60gig. Thats just a bit of an eduated guess.

I think you're still looking around the 1100 - 1300 dollar mark.

I get the feeling though that some time in the future sony may release a fully software emulation of the ps2 hardware for ps3. And then you won't need to get a 60gig. Thats just a bit of an eduated guess.

i got a feeling a chip is on the way letting u play copied/downloaded games as well as PS2 games...maybe more :yes:

  • 2 weeks later...

query:

Q6600 @ 3.60 ghz (2.4 stock) G0 stepping model

2900xt (two-off) with coolermaster glacier-600 water cooling

thermaltake bigwater 735

70degrees core 0, 69 core 1, 67 core 2, 66 core 3

on full load

is that too hot?

bearing in mind the graphics cards idle at 49degrees

runs at 47-44deg on idle

pump - cpu - pcie - pcie - radiator - reservoir - pump

had a nth bridge water block as well, but not on atm

might have to refit it along with the double radiator - just that the extra radiator has to sit outside the case :)

Yeah man that is WAY too hot for a water cooling system. I would turn your voltage down a tad - but you may have to lower your fsb too. What voltage are you currently running? I would think around 3.8v, which is probably too hot. Your CPU won't have too longer life at that rate. 44 degrees is way too hot at idle too.

Should not even be that hot with a really good heatsink and fan.

Put more case fans in and get more air flow will cool it down heaps. I have 2 x intake and 2 x outlet fans, plus the CPU, VGA card and dual PSU fans. There is no such things as too much air movement. Is the fan working properly on your radiator? I think it may not be - that would be your problem.

yeah thought so

better rejig it and add the external double radiator/fan system (its a 745 system, but only setup the small single radiator)

:)

the 2900xt's used to see 100degrees on air (stock) on load, so the water has brought them down by 35degrees

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Is this where I say "Hey man my airbox cost me horsepower in my Naturally Aspirated Engine"? (I know you need them for legality in NSW)
    • 1.5mm alloy folded up, it will need a tweek, as the angled bend only got to around 45° as that was the max that the break press would get with the other bends, and I needed a fair bit more, but and the alloy is easy to bend too my will by hand once I trim the lower section out I'll Dremel out and form the angle and mounting point on the lower section when time permits  As for the lid, I'm looking at going a "cap", instead of a flat lid to hide the fixtures a bit
    • I got sick of thinking about batteries so just kept buying chargers. I've got a ctek (racecar), a "noco" thing from supercheap (tow car with 2 batteries), and an old "SupaCharge" branded lead acid thing (farm ute/mower) and will need 1 more when the Silvia gets a battery again (if the 86 stays).  I always make sure the charger itself is in free space/away from car etc, just to be sure.   
    • The "long nose" diffs in your type of car, that have the speed sensor on the snout, are a pain because the casing is different from all the other short nose diffs. This means that the pinion shaft inside them is longer, which can make it harder to do certain types of diff swaps. But, if all you are going to do it swap the diff centre, and keep the gears (that's the crownwheel and pinion gears) then you won't have any problems.
×
×
  • Create New...