Jump to content
SAU Community

Recommended Posts

mine is doing that, ideling at 1500/1400rpm

Its the round gold thing with an electric clip going into it, its connected to the AAC valve. (on the back of the intake plume)Thats what mine was.

u can test it by disconecting that clip when the car is on. if its working the revs should change. if the revs dont change its stuffed

Link to comment
https://www.sau.com.au/forums/topic/109036-idle-speed/#findComment-2011623
Share on other sites

mine is doing that, ideling at 1500/1400rpm

Its the round gold thing with an electric clip going into it, its connected to the AAC valve. (on the back of the intake plume)Thats what mine was.

u can test it by disconecting that clip when the car is on. if its working the revs should change. if the revs dont change its stuffed

where abouts is the gold thing located?

Link to comment
https://www.sau.com.au/forums/topic/109036-idle-speed/#findComment-2011832
Share on other sites

to find an air leak buy a can of carby clean and spray around suspect area. when revs pick up you have found you mark......dont use water on things limke manifolds for air leaks.....water doesnt compress like air and has a tendancy to bend bits inside motors if to much goes in......:D

Link to comment
https://www.sau.com.au/forums/topic/109036-idle-speed/#findComment-2019794
Share on other sites

ok, have noticed that the problem is mostly in the morning....

i have tried letting it warm up for a while, but it doesnt go away

if i goto work in the morn, park it and say start it at lunch, it will rev just under 1000rpm

its almost everyday that this happens and its rather annoying....

will have a play around on the w/e

thanks guys

Link to comment
https://www.sau.com.au/forums/topic/109036-idle-speed/#findComment-2021355
Share on other sites

has anyone thought about the throttle cable?

it may be sticking a bit!

my 32 idels around 900-1000rpm an sumtimes it idels at 1900- 2000rpm then drops back down to normal rpm. an because the the throttle cable is sticking a bit.

ahhh who would of thought of that.

Link to comment
https://www.sau.com.au/forums/topic/109036-idle-speed/#findComment-2021444
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
    • Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity. Edit: 11kg each (or 10.9/11.1 depending on what my scale decides over multiple tests, the 18x11 don't seem to weigh noticeably any more than 10.5)  
×
×
  • Create New...