Jump to content
SAU Community

Recommended Posts

Hi Guys,

My wing's brake lights seem to have died. I ripped them out to test various things, and the car's putting 12v up to the lights fine...

Anyway, I'm in the market for a replacement. It's a stock R33 GTS-T type-m wing. Anyone know who's the best person to see about these things? Or perhaps someone has a spare one lying around collecting dust?

Link to comment
https://www.sau.com.au/forums/topic/10907-wing-brake-lights/
Share on other sites

I remember reading about this a longtime ago.

Apparently the lights are all LED's wired in series so they can take the 12v.

The bad thing is if one stuffs up the whole lot won't light up (cause they are wired in series).

Pull the light out of the spoiler and check each LED, when you find which one is stoofed just replace it.

The hard part will be finding a replacement LED the same brightness as the others. Might be easier to replace them all so they all look the same.

J

Link to comment
https://www.sau.com.au/forums/topic/10907-wing-brake-lights/#findComment-178715
Share on other sites

I assume you mean the series 1 spoiler, the curved one that sort of rounds off the back end?

Yes it is a pain to get the lights out of it, the best way is a ratchet with a screwdriver bit, works a treat. Also, I believe the LEDs aren't strictly in series - they are grouped into lots of 5-10 LEDs, and all of the groups are wired in parallel, so that if you blow an LED, only the group that it's in is affected, not the whole array.

Link to comment
https://www.sau.com.au/forums/topic/10907-wing-brake-lights/#findComment-179677
Share on other sites

thats right with what Revhead said, they are in groups, i had a few out on mine when i first got it, it is an aftermarket GTR wing but the principal is the same, it had actually got water inside the casing of the light and corroded part of the circuit board away, re-soldered it back together and put some silicone around it all and it worked a treat, it was just a hassle to take out as the whole wing had to come off.

Link to comment
https://www.sau.com.au/forums/topic/10907-wing-brake-lights/#findComment-179765
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...