Jump to content
SAU Community

Recommended Posts

Yeah you always get people tagging along or adding them selves on half way thru a cruise its cool tho!!. If I saw 50 skylines go past or in a carpark I would be following them....

Do the cops know about this cruise??

Just Curious

:P

i will let the POLICE know just before we go :D

  • Replies 283
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

There is no difference, except there will be more cops, guarunteed radars, more attention... it's just more fun if you dont have to constantly watch your speed and watch your back for cops... I never speed excessively, but double demerits weekends are when they are out there specifically to hit you up for 6 points for doing 16km/h over the speed limit. Fawk that!

90KM/h is so damn slow...

I just went to the central coast from lidcombe... 15 cops on the way!!!

Be careful peeps!

OMG!!! I just noticed this, it will be so usedful!!! :P

so is this cruise open to stageas?

i still come from the nissan family...

anyhow were from newy so we'll meet you guys when you regroup off the freeway..

any idea's on what tym or near abouts to what tym you will be nearing there?

the other half is up for it too so he'll have his car as well.

so add us to the list of definates mum's taxi and brizzi

Hey can you tell me what time do you think you will be getting to the twin servo's we want to meet up with you guys there cause it to far to go to homebush from East Lindfield or what time you think you will be hitting the F3?????

Cheers

Andrew

anyone going to the cruise from sydney's west? i might be going, would be good to meet up with some westies first, then take off.

meet up at Hungry Jacks, Cumberland Hiway at 9:00am for a sharp 9:30am departure to Homebush P6!!!

i think a few of us may be meeting you (e.g. me - if i can make it, rb30gtr etc) lot at the F3 start - do you guys have an ETA for when you'll be at the F3 start ???

guys just to let you all know, we will be departing P6 at 10:30 sharp, so please do not be late we will not wait for you.

if things goes to plan, we will be on the entrace of the F3 by 11:15am, so if you guys just wants to stop one one of the sides st till u see us coming, if not we will have radios on, will confirm channel, if not you guys can call me on 0404316910, and just check wif me how far we are.




  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...