Jump to content
SAU Community

Queensland Wasteland


Recommended Posts

  • Replies 28.4k
  • Created
  • Last Reply

Top Posters In This Topic

  • chaos

    4853

  • BelGarion

    4045

  • GTS-t VSPEC

    2546

  • rb25

    2007

Top Posters In This Topic

Guest 87vlt
Originally posted by BelGarion

yer good, yer another ****ing dickhead attacking me again

your right man, i wouldnt have a clue cause my boost guage says 7psi and it doesnt waver till later in the rev range for 9psi, once it hits these marks it doesnt move, mabey i should throw it out

its a ****ing catback u tool, thats it, the boost does not spike, jump or whatever, but then again what the **** would i know, its not like i have a clue what the **** im on about,  there is no ****ing bleed valve, there is no punched out cat or dump pipe or anything, yet im running 14.1, so mabey willowbanks timing gear is ****ed too, got anything else to blame it on?

you ****ing got up people for raggin on your car, your no bloody better yourself you jerk

9 psi is a bit higher than the stock 7 psi ...... I think it has made a difference by putting on a cat back exhaust ..... god damn you take shit to seriously, my point was that was quicker than the supposed 14.5 times nissan quotes. Which I'm happy for you.

Guest Boxhead

i like that last post :)

thats the way we all should care about it..

hahaha, well atleast i do..

umm but seriously guys, even iff for eg, i was to run my car on the 1/4 and i was getting shitty times, then i for some reason started inscreasing without mods...

dont you think maybe ive fine tuned my dragging technique..

and 87vlt - dont whinge about that, coz you know you were annoyed when someone else did it to you

Guest 87vlt
Originally posted by BelGarion

im complaining bout bein single

oh and i ripped into 87vlt for accusing my car of running more boost than the boost guage says

Seriously man stop getting abusive otherwise you'll end up ban like I was. I want to discuss this in a mature manner. Where do I meantion a boost gauge? I said stock boost ..... not what your boost gauge said. You don't need a bleed valve to increase boost by small amounts. Small changes like the strength of the actuator pull, more free flowing exhausts, etc increase the boost, only slight but its still there. This is what I believe has contributed to you getting such a good time with a car thats almost stock car and dude you should care cause its not just a car that gets it to those times.

ill take the catback off, it will still have 7psi below 5000rpm and 9psi above 5000rpm

thats the way r33s are from factory.....

hell if ur that desperate to prove it wrong, ill take my exhaust off and drive it round the block

1. ull see no change in the boost

2. ull pass out from the gasses

3. cops will be called cause of noise

but it will still be 7psi below 5krpm and 9 above it

or you could make up an exhaust that goes from the turbo down to just under the firewall, and drive around on the road like someone i know, who was subsequently caught and fined.

Sounds wicked, turbo spools so loudly, neighbours dont like it so much.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...