Jump to content
SAU Community

Recommended Posts

Heya all,

Same old problem. Drive around, then put it in neutral. Car drops to around 500rpm, then stalls.

I cleaned the AAC like nobody's business, and still no luck. I'm running an aftermarket BOV, but am

plumbing it back.

Visually inspected the AFM and it seems fine. Is there any way to tell if it is the cause of the problem?

If I can't fix it myself, I'll have to fork out big dollars to get everything inspected one step at a time.

I've heard rumours of an idle speed control solenoid, air regulator or throttle position sensor, but the details

on them were sketchy at best.

Please help me out,

Thanks,

Adrian.

Link to comment
https://www.sau.com.au/forums/topic/109749-yet-another-stalling-problem/
Share on other sites

Just found out that with the A/C on, it wont stall. So I'm writing it off to an rpm setting issue, and will turn up the revs on the old girl, see if that sorts it out.

Will post the results on here either way.

Thanks,

Adrian.

As an update, I cleaned the AAC, it's sparkling inside now. Put it all back

together without a drama, and it still stalls.

Other causes I've read about are as follows:

AFM dirty or oily

Fuel Pump earth wire

Fuel Filter clogged

Throttle Position Sensor needs adjusting

Crank Angle Sensor needs adjusting

I'm going to attack my AFM with carby cleaner tonight and see if that makes any difference. If it STILL stalls, I'll look into disconnecting the AAC plug, and check if that stabilized idle. If it does, I might not bother re-connecting it.

I'm also planning on changing fuel filter, and fitting iridium spark plugs.

Will eventually find the gremlin, then I'll let you all know :O

As an update, I cleaned the AAC, it's sparkling inside now. Put it all back

together without a drama, and it still stalls.

Other causes I've read about are as follows:

AFM dirty or oily

Fuel Pump earth wire

Fuel Filter clogged

Throttle Position Sensor needs adjusting

Crank Angle Sensor needs adjusting

I'm going to attack my AFM with carby cleaner tonight and see if that makes any difference. If it STILL stalls, I'll look into disconnecting the AAC plug, and check if that stabilized idle. If it does, I might not bother re-connecting it.

I'm also planning on changing fuel filter, and fitting iridium spark plugs.

Will eventually find the gremlin, then I'll let you all know :thumbsup:

Did you adjust the idle speed using the screw in the base of the AAC (driver's side)?

Clogged fuel filter usually has the opposite effect - idles fine, won't accelerate.

Just took my car for a spin and had a thought:

I noticed that when the boost gauge reads -0.6 on idle, the revs are around 650-700rpm. However, after driving then clutching in, the boost gauge drops to around -0.8, then slowly comes back up to -0.6.

My question is - is this cause or effect?

Is the low boost gauge reading causing rpm fluctuation, or is rpm fluctuation causing varying boost level readings? Or are both of these effects of the same cause?

Thanks pal. I took the AAC off the car and cleaned the sh*t out of it

with carby cleaner, got it looking real schmick. Then I put it back on and

hey presto - no difference... :D

I heard that disconnecting it can correct the problem, but then it runs a

certain rpm idle no matter if A/C is on or off. I would rather fix the

problem properly, if I can.

Thanks a bunch for your help.

Okie dokie

I didn't mean take the AAC off (as that would obviously leave a giant gaping hole out the side of my inlet manifold).

What I meant was disconnecting the plug that goes to the AAC.

Edited by Johnny Cash

ok, here is procedure to check your AAC valve properly. you'll need a multimeter.

my guess is either voltage between pin 1 and ground will be wrong, or the resistance between pin 1 and pin 2 are wrong, if everything is fine start looking at other things.

(sorry about the large images...)

aac1.jpg

aac2.jpg

aac3.jpg

aac4.jpg

aac5.jpg

aac6.jpg

hope this helps :D

Well it certainly looks like a lot of words and fancy pictures. Pity I know nothing about this sort of stuff. If I can't fix it with a screwdriver and a hammer, then it's beyond me.

Multimeter? I wish!

i dunno if this will help but, since uve mentioned that ur running with an aftermarket bov, have u tried putting a different bov? or installing ur stock one back? coz some ppl had this problem and usually the bov had been leaking or something like that, hope to be in help

Nah it all works a treat now. I just cleaned the AAC and AFM.

I used carby cleaner for the AAC, and electrical contact cleaner for the AFM.

Purrs like a kitten, thank god. Let's just hope it stays that way.

Thanks for all your help, guys.

She almost stalled on me this morning, but she was cold, and I was running my BOV atmo, so they could be causing it. I'll tighten the sh*t out of the BOV when I go home for lunch, and see if that makes a difference.

If it only happens when its cold, I'll let it go. It's when it's warm that it concerns me. It's hard to get going in the morning, like its owner :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...