Jump to content
SAU Community

Recommended Posts

Please e-mail me if you're interested in having your car remapped while I'm in brisbane....

Dates are 10th and 11th April

Will be held at DynoSource in Nerang.

LIMITED PLACES - Book Now!

E-Mail Only PLEASE - [email protected]

Link to comment
https://www.sau.com.au/forums/topic/109983-retune-your-factory-ecu-10-110406/
Share on other sites

I remap most Nissan ECU's and the result is often better that most aftermarket computers and the total cost is substantially less. Significant gains can even be made on standard engines.

I would like to suggest that ALL vehicles have upgraded fuel pumps (standard are way bad), full tanks of whatever petrol you want the car tuned on, maintained vehicles (serviced, good spark plugs etc).

Remap Prices cover initial ECU modifications, and loading of pre-tuned maps to suit, these will then need 1-1.5 hours of dyno time tuned specifically to your vehicle and fuel. Dyno time as mentioned will be around $180/hr. ECU modification and Base Maps priced as follows:

S13 CA18 - $330

S13 SR20 - $450

S14 SR20 - $660

S15 SR20 - $660

R32 RB20 - $330

R32 RB26 - $330

R33 RB25 - N/A

R34 RB25 - $660

Z32 VG30 - $330

Chaos - Sure Why not, if it saves me a few hours of stress trying to get a micro guess right.... What loom is in the car?

Dave - S2 and S1 are the same.... I do have a package where I can offer a remapped R32 ECU and use an external VCT controller (like buddy club for $85 I heard)

Just quick one for RB20 people. I had mine done last time Sam was up. Worth every cent hey. And I didnt need the dyno time, just did a quick test and afr almost straight line on 12. Not saying you wont need dyno time, but if you have minimal mods, and it comes out ok, its really good value for money.

I would highly recomend it.

Chaos - Sure Why not, if it saves me a few hours of stress trying to get a micro guess right.... What loom is in the car?

Dave - S2 and S1 are the same.... I do have a package where I can offer a remapped R32 ECU and use an external VCT controller (like buddy club for $85 I heard)

Its an R32 loom, but doubt the car will be back on the road in time, and if it is i wont be able to afford the tune. Maybe next time your up.

Dave - S2 and S1 are the same.... I do have a package where I can offer a remapped R32 ECU and use an external VCT controller (like buddy club for $85 I heard)

Are you sure?? I have recently had to replace my factory ECU on a R33 S2 (1996) and we tried four Series 1 ECU's and they wouldn't even talk to the car. Borrowed one out of a R34 GTT (1998) and it was perfect. Same sticker and serial numbers also.

Moot point for me anyway as I now have a haltech. Thanks for your time though.

Dave

I stand corrected, if you still have your ECU can you take a photo with it's lid off so i can see the board? I may be able to remap them like the 34's :(

Sam.

Edited by Dr_Drift

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
    • The BES920 is like the Toyota Camrys of coffee machines. E61 group head is cool, however the time requirements for home use makes it less desirable. The Toyota Camry coffee machine runs twin boilers and also PID temp control, some say it produces coffees as good as an E61 group head machine.
    • And yes with a full tank it will hit limiter free revving or driving 6B6CDF6E-4094-426D-A9CB-6C553475FE36.mp4
×
×
  • Create New...