Jump to content
SAU Community

Recommended Posts

Have been getting only 20 miles / gallon from my 93 r33 gts-t 4door auto. Has new NGK Iridium plugs and I use BP Ultra and 10 pounds boost.

Bought the car and had them up the boost to 10lb b/4 I took possession of it, so I don't know what the fuel economy was b/4.

Many people on the net say they get between 26-30 mpg so I was a little concerned. Had a mate of mine who works for one of the Nissan dealers check it out and all the data came up ok.

He said that it must be a combination of being an auto, the upped boost and a bit of a lead foot that is contributing to the low fuel economy.

Just interested to know what some of you guys are getting economy wise.

Thanx

Ric

Link to comment
https://www.sau.com.au/forums/topic/11100-fuel-economy-or-lack-of-it/
Share on other sites

I have no concept of how good or bad 20mpg is. I don't even know how to do the conversion.

My car gets 14-16L/100km around town (usually just under 15) when running at 0.8 bar boost. At 1 bar it is usually just over 15. I am experimenting with a tankful on 0.6 bar to see how much fuel I'll save, if I gain another litre/100km I will set it to 0.6 when I'm low on cash and need to save money on fuel :D (I love EBC's!)

On the highway I get 9.5L/100km on .8 bar and 10.5L/100km on 1 bar. Keep in mind that this is with a lot of spirited overtaking. It's the main thing that keeps me awake!

Man I hate this L/100km crap, makes it really hard to work out how far you can go on one tank on fuel. Sod it, I'm going to start doing kilometres per litre too, starting right now.

14L/100km = 7.14km/L = 428km per tank (fill up around or before 400km)

15L/100km = 6.67km/L = 400km (fill up ~370)

16L/100km = 6.25km/L = 375km (fill up ~345)

9.5L/100km = 10.53km/L = 631km (fill up ~600)

10.5L/100km = 9.52km/L = 571km (fill up ~540)

If I had been working off kilometres per litre instead of this stupid L/100km crap I could have saved myself from a huge stuff-up in refill planning on a recent holiday trip up north. I wasn't sure if I had enough fuel to make it to the next available servo on a round trip while in the area and ended up running around for an extra 60km that I later discovered I didn't have to (long story).

Thanx guys, I guess it must be my fault that this cars is an gas-a-holic.

I deal with metric measurement all day in my work and also relate things back to imperial often, but this litres/100 km has always pissed me off.

My daughters boyfriend is only 21 years old and knows perfectly well what miles/ gallon is.

Thanx again

ric

Originally posted by hippy

how did u get 9.5/100km??  long highway drivin??

Actually, it was my gf taking the car up north from Sydney to Taree (about 300km) to visit relatives, then back again. Worked out to be 9.5L/100km when I did the mileage when she got back. We both then travelled back up the same day (she had to come back to Sydney for a job interview) and I decided to experiment with the boost pressure and set it to 1 bar.

I got 10.6L/100km for the trip up, and 10.4L/100km for the trip back. It was slightly worse on the way up because we had a little bit of city traffic to get out of before hitting the highway.

I guess I should have kept my mouth shut. Some of you guys are doing worse than me . Last fill up was 320km from 45litres, around 20MPG

Realisticly, I shouldn't complain as my Bedford van (work van) with a 400 Chev gets around 12 MPG. It carries a fair bit of weight though.

Guest KILLER-T
my Bedford van (work van) with a 400 Chev
Sorry to get of topic but i seen this bedford van at the end of the midland bypass a while ago it lined me at the lights and took off like a rocket (well it looked fast for a bedford) MMWAHAHA a bedford tryin to chop a SKYLINE :shake: :shake:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I had 3 counts over the last couple of weeks once where i got stranded at a jdm paint yard booking in some work. 2nd time was moving the car into the drive way for the inspection and the 3rd was during the inspection for the co2 leak test. Fix: 1st, car off for a hour and half disconnected battery 10mins 4th try car started 2nd, 5th try started 3rd, countless time starting disconnected battery dude was under the hood listening to the starting sequence fuel pump ect.   
    • This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
×
×
  • Create New...