Jump to content
SAU Community

Recommended Posts

Well i'm pretty sure my powerFC has taken something up the ass. I was driving along last night, not even giving it stick and the engine just died. pulled over, the hand controller isn't lighting up and it's not switching any of the relays (Eccs, fuel pump etc) that it normally does. All of the wiring to it is intact, and none of the fuses have blown.

So is it possible to take it somewhere to get fixed/diagnosed etc? i'm reasonably handy with electronics but when it comes to testing chip outputs and memcals etc i'm out of my league. i'm going to see if i can test it by putting it in someone else's car (skyline R33 - any takers in brisbane?) but i have a feeling something is wrong with it.

ECCS line was fused to 7.5 amps btw, everything else was factory VL body fusing. there are no burnt solder tracks on the PFC board.

any ideas?

cheers,

Stocky

Link to comment
https://www.sau.com.au/forums/topic/111001-is-my-powerfc-dead/
Share on other sites

First step would be to check that it is still getting power from the ignition on pin 45 and also whether it is still getting the constant battery back up.

Try www.petroject.com.au the parramatta branch definately does work on pfc's but there are branches all over australia which may also be able to help.

okay so the wierdest shit just happened. i can't explain a lot of it, but here we go:

went out to the car this morning, same as last night. no lights on the controller, no relays clicking at all. so i check the power inputs everywhere. that's funny - the constant 12V line isn't getting power. so i trace the whole thing back into the engine bay - lucky i knew exactly where it all went because i wired it up. turns out one of the terminals right up near the battery on the fusible link had corroded just enough to kill my power at 12.30 this morning in the middle of the city. :O

so i re-supplied it, no worries! oh shit, still no power on the hand controller. turns out the IGN fuse had blown. threw another one in. still nothing. so i bridged the fuel pump relay wires, but it wasn't going. however, when i bridged them, the hand controller turned ON. WHAT THE HELL?

now it has power, but the fuel pump isn't going. there is a fault somewhere in the line.

so i laboriously made a whole new wiring section from the battery in the boot to the 044, using a new relay and thick guage wire etc. magically, the car turned over and purred like a kitten. a kitten of spite.

thank god it wasn't the PFC, i don't have enough cash for a decent gearbox AND a new computer.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
    • Yes then it will turn on but I want the car features to work  
    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
×
×
  • Create New...