Jump to content
SAU Community

Recommended Posts

  • 3 weeks later...
  • 2 weeks later...
  • 4 weeks later...

Stupid rain only got 3 runs :miner:

Best time:

13.239ET 2.20360ft 110.42Mph New PB! <room for improvement>

My best 60ft of the Night: 2.150 (clutch smelt good afterwards changed to 2nd too early and got the worst time of the time)

Best MPH 111.27(179.08km/h)

Sau Nsw 400m Registry

GTR

DiRTgarage: 10.36 @134mph r32 gtr (two.06l stacey 11.95 @121 mph)

SCOOP: 10.9 @ 127.40mph r32 gtr

T04GTR: 11.7 @ 116mph r32 gtr

wrxhoon: 11.8 @ 117mph r34 gtr

hot53x: 11.961 @ 112.77mph r32 gtr

Blitz: 12.0 @ 111mph r33 gtr

benm: 12.3sec @ 113mph r32 gtr

OFENSV: 12.123 @ 114.50mph r32 gtr

hanyou: 12.427 @ 111.95mph r32 gtr

JET-32R: 12.49 @ 106.66mph r32 gtr

Morgs: 12.53 @ 111 mph r32 gtr

GTRsean: 12.5 @ 116 MPH r32 gtr

GTR-27L: 12.7 @ 105mph r32 gtr

MIKE_R32_GTR: 12.851 @ 105mph r32 gtr

GTS-t/ GTT

MR331307: 10.8 @ 128mph r33 gtst

2RISMO: 11.662 @ 118.3mph r33 gtst

RNMENC: 11.75 @ 121mph r33 gtst

itboom: 11.8 @ 122mph r33gtst

ECR033: 11.945 @ 118.27mph r33 gtst

DoughBoy: 12.0 @ 123.7mph White car r33 gtst

DoughBoy: 12.1 @ 119mph Black car r33 gtst

88silhouette: 12.119 @ 111mph r31 sil

OFENSV: 12.175 @ 118.14mph r33 gtst

legend01: 12.220 @ 111mph r32 gtst

qwikky: 12.3 @ 109mph r33 gtst

moanie: 12.504 @ 112mph r33 gtst

abobob: 12.764 @ 106mph r34 gtt

mass iv: 12.91 @ 111mph r33 gtst

Guilt-Toy: 12.98 @ 108mph r33 gtst

yogi000: 13.1 @ 108mph r32 gts

ru3-29T: 13.3@ 105mph r33gtst

spx25t: 13.354 @ 103.23MPH r31 25t

race_snooze: 13.4 @ 111mph r33 gtst

cerci: 13.522 @ 103mph r33 gtst

GTshortie: [email protected] r33 gtst

kennedy: 13.615 @ 102.42mph r33gtst

silver gts-t: 13.62 @ 103mph r32 gtst

trust33: 13.6 @ 102mph r33 gtst

cuong nguyen: 13.761 at 106mph r32 gtst

RedDrifter: 13.7 @ 105 mph r32 gtst

cohen20: 13.7@?? r32gtst

JAS-25T: 13.8 @ 99mph r33 gtst

burnsie: 13.900@98mph r32gtst

SECUR1TY: 13.902 @ 101.36mph r33 gtst

Shonen: 13.934 @ 97.4MPH r34 gtt

JeeTeeEss25Tee: 14.01 @ 100.58mph r33 gtst

nath95: 14.04 @ 99mph r33 gtst

MaTBoY: 14.09s @ 99.55Mph r32 gtst

Siddr20: 100.15mph r33 gtst

mr moo: 14.191@ 96.76 r33 gtst

mike1987: 14.2 @ 97mph r32 gtst

jf R33: 14.258 @ 100.66mph r33gtst

tomm0: 14.3 @ 98mph r33 gtst

raz0r$harP: 14.516 @ 95.98mph r33 gtst

evil_weevil: 14.5 @ 94mph r33 gtst

d00dz: 14.53 @ 102.5mph r33 gtst

Tebie: 14.572 @ 94.24mph r32 gts4

sindows: 14.8 @ 96mph r33 gtst

the R32: 15.0 @ 101mph r32 gtst

Other

Boosted Zed: 10.709 @ 139.67mph 300ZX

Barry: 11.1 @ 123mph datto 1600

ido09s: 11.274 @ 121.79mph S14a 200SX

NBP: 11.8 121mph rx3 13bt

bmxwrx 12.4 @ 112mph MY00 WRX

TommO: 12.6 @ 108mph Evo VIII MR

DVS>VLT: 13.6 @ 104mph VLt

wokburner: 13.02 @ 109mph 300ZX TT

BLISTIC: 13.0 @ 109mph 180SX

PORTS: 13.433 @ 105.39mph z32 300zx

Felix st: 14.7 @ 94mph 98 Honda Integra VTIR

Will be updated. :laugh:

Edited by johno_shaun

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...